Thanks John,

Good plan to support the staking as much as possible till we get all this sorted out
and once it is the Masternodes rewards will then increase exponentially.
Best to resend yourself most or all your wallet balance to one or a few addresses
every 3-4 days to provide you  the best staking returns.


MikeMike

I agree and asked a few hours back it be added to the revised version.

good job KORE crew!  i'm looking forward to more tech to roll out.

I'm rocking a "few" masternodes and staking bunch to support the blockchain.

Go KORE, Go BTC

NOTE:
If you have KORE staking could you consider to put this in your kore.conf file:
setstakesplitthreshold=2000
It will stop splitting your amount into half once it is below 2000 KORE.
Close your wallet, update your conf file with it, send all your KORE to one or more addresses if a large amount.
You could change the 2000 to be a bit more or less if you like or not do it at all.
This could help you stake better till we get the update finished.


MikeMike

Your VOUT info is not right. You have 501 sent and may be backwards normally the 500 is at the top where the 0.26xxx is. It needs to be 500 exactly and then pay extra for the TX fee. Also, did you keep the coin in the local wallet or did you send the coins to somewhere else? If you make a new Address and send them From the Local Wallet to the new Address in the Local wallet, the coins have to stay there for the masternode to be valid.

Is this what you see when you decoded RAW TX in the console? If not then post your TX or the Console for the RAW TX. If you are on a windows local wallet you may have problems too. I tested on windows and it locked up until I took out the masternode info.

 "vout": [
      {
         "value": 0.26238329,
         "n": 0,
         "scriptPubKey": {
            "asm": "OP_DUP OP_HASH160 001cf85f9594a8597b71731b0c8320aa37354295 OP_EQUALVERIFY OP_CHECKSIG",
            "hex": "76a914001cf85f9594a8597b71731b0c8320aa3735429588ac",
            "reqSigs": 1,
            "type": "pubkeyhash",
            "addresses": [
               "K7Dk1mmNDNmgPyqM8SMf4XpPc4cpwuCEiw"
            ]
         }
      },
      {
         "value": 501,
         "n": 1,
         "scriptPubKey": {
            "asm": "OP_DUP OP_HASH160 af5d2cbc993876a35f2f703dea10bc6b0c5487cb OP_EQUALVERIFY OP_CHECKSIG",
            "hex": "76a914af5d2cbc993876a35f2f703dea10bc6b0c5487cb88ac",
            "reqSigs": 1,
            "type": "pubkeyhash",
            "addresses": [
               "KPCPBMRPHMByyCXZZjJAW3beKGf5p43pTd"
            ]
         }
      }

I'm on win7 pro 64 & all seems to be working well locally except the wallet hangs every time when closing. Hopefully this is fixed in update.

The (10)MN's are hosted via vultr running ubuntu 17.xx. So far so good with vultr.  https://www.vultr.com/?ref=7265944 They bill by the minute which is cool($5 month) and the ability to one click reinstall is great for a linux noob like me. I've wanted to be a "linux guy" for years just too busy and lazy. Fail Me     KORE step by step MN setup instructions are par to none. Kudo's to whomever put that together.

all the best,
john

@mikemike

Congratulations on bringing KORE this far.

I've been holding KORE for at least a couple years and one consistent memory is you being in contact with the community during the darkest of days.

"I believe in KORE" and "you will be glad that you stuck with KORE" resonate when I look at where KORE sits technologically today and the currrent value of my KORE holdings. I lol reading that because the value of KORE has yet to be realized.


Thanks to everyone @ team KORE.

Dawn is beginning to reveal itself. 2018 is going to be complete madness 

john

I think the price correction of Kore is over and from now on we will start climbing again. Soon we will be back over 5 dollar.

I am now able to start the masternode on my local wallet. Status has turned to 'Enabled'... However when i go back to my ubuntu VPS and check on the masternode status by typing 'kore-cli masternode status', i'm getting a different status... i got...

{
   "vin": "CTxIn(COutPoint(000000000, 4294967295), coinbase)",
   "service" : "[::]:0",
   "status" : "Not capable masternode: Hot node, waiting for remote activation."
}

So how do i send an activate from my local windows wallet?

Thanks.