your pool looks like it has been on the right chain and is still looking good. i remade my account with he same email and username do you need more info?

Works for me, wallet reports v2.0.1 but I'm connected just to nodes which report v2.0.0 so a bit confused about versions - what are differences between v2.0.0 and v2.0.1  

Net hashrate reported by wallet is wrong, is shows just 0.151 MH/s for PoW difficulty at around 155k and also network stake weight value is missing (wallet is locked, do I
have to unlock it for value to show up?).


I think PoS reward is based on total network weight - the more TEK are mature, the lower is reward. Difficulty is there just to attempt to keep block generation rate at 1 minute
on average.

the first tekcoins staked would have been 30 days after mintage started and likely blocks of 1, starting diff then would begin to adjust. it appears the pos diff adj is working and that includes changing the payout %.

here is some copy pasta

  // tekcoin: reward for coin-year is cut in half every 64x multiply of PoS difficulty
    // A reasonably continuous curve is used to avoid shock to market
    // (nRewardCoinYearLimit nRewardCoinYear) ** 4 == bnProofOfStakeLimit bnTarget
    //
    // Human readable form:
    //
    // nRewardCoinYear = 1 (posdiff ^ 1/4)


you can look at lines 975-1015 here https://github.com/maxxine/TEK/blob/master/src/main.cpp for more

"Works for me, wallet reports v2.0.1 but I'm connected just to nodes which report v2.0.0 so a bit confused about versions - what are differences between v2.0.0 and v2.0.1  Huh"

2 is the new wallet old gui, 2.1 is the new wallet new gui both are good

64.188.164.77  leave this one out. It's my ip, and it's going to go away tomorrow most likely, as I'm moving. It's a good node until I take it down, so no worries, but I'd take it out of your configuration to avoid any problems when I go offline. I'll probably be offline for like a week to ten days, or very spotty if I am online, and then I'll be a solid node again.

David, you probably have a better understanding of this than I do, but I think the NVCS adjusment will calm down in a few days, so if all of us use coin control and stage our staking, it likely won't go nuts again, barring further catastrophe.

Thundertoe or Defaced can correct me if I'm wrong here, but I believe they are going to release another wallet with checkpoints and exclusions very soon, but it will NOT be a mandatory update as this last series was because the checkpoints and exclusions will be the only change. That being said, there ain't no good reason NOT to update when that happens.

I personally think IRC is a disease, but in this instance, I have to agree with your assesment. Either that or a skype room for the duration of any emergency.

Where is unlock wallet buton on new gui?

Thanks Biomech and xhabit
Updated version

A. Salvaging
1. (awaiting confirmation) We finally have a working TEK again - no more forks - https://bt.irlbtc.com/view/320404.msg8565376#msg8565376. Still,it would be best (but not necessary) to wait for a pending release with checkpoints.
2. (awaiting confirmation) Do NOT start up the old client. Get the latest version instead.
3. (awaiting confirmation) Do NOT use the older blockchain. Sync everything from scratch (so, delete yourtekcoin folder EXCEPT your wallet, of course). A blockchain is available to download somewhere (please point the URL, update the OP
4. (awaiting confirmation) Ideally, use a backup of your wallet, not the latest version of your wallet, which might be on the wrong chain from the past ten days
5. While you're at it, create a tekcoin.conf file like this one
put this in tekcoin.conf (thanks to oto3):
connect=74.196.63.95
connect=75.90.67.140
connect=68.229.91.209
connect=108.59.185.202
connect=98.236.102.116
connect=75.91.15.240
connect=94.156.230.246
connect=212.21.68.60
Notice I thought it is supposed to be addnode=.
6. (awaiting confirmation) If you want to have something closer to the advertised 40%, do NOT stake now (and thus, do not leave you wallet open more than for checking it works). Please note this is not an evidence that NVCS is really working as it should, only that under exceptional circumstances, it does sort work - but this is still not sure it works as intended. Presstab, can you elaborate on this, regarding the TEK NVCS that could still be broken even after the fix? elaborated on this.
7. (awaiting confirmation) It would be good to check your wallet. Repair wallet and --salvage wallet would make sense, but more explanations needed here
8. (awaiting confirmation) Update the OP with instructions.

B. Observations
1. In the future, dev should use #tekcoin (IRC @freenode) or (Skype or any instant messenging people are comfortable with) instead of bitcointalk. This is much faster for debugging.
2. I would welcome a debriefing. What went wrong (biomech wrote up a nice summary), what can be done to improve the process (PDCA/Deming wheel), like setting up a testnet, preparing a checklist before release...

If you set a encryption on the wallet (password) it will magically appear   If you don't have password set, you don't need it anyway

Thanks presstab. I updated my previous post accordingly.

The ELI5 version (presstab, don't hesitate to correct me) is that the NVCS code is not smooth enough; it kicks in late and when it kicks in, it kicks hard and this hurts. HYP code is smoother, less painful to users.
For people familiar with Monero and PoW, consider NVCS as block halving and HYP staking (we have to find a better name, press) is continous decrease.

Thanks for these explanations, stop believing that I know more than you do

---

By the way: I can't compile TEK's new version because it is looking for mingw-specific libraries (-lboost_system-mgw48-mt-s-1_55 -lboost_filesystem-mgw48-mt-s-1_55  -lboost_program_options-mgw48-mt-s-1_55 -lboost_thread-mgw48-mt-s-1_55). Sure, I could manually edit the makefile, but that's not the point of compiling from source to manually edit and I don't know how to commit a tekcoin-qt-linux.pro file (which should be updated manually everytime the tekcoin-qt.pro file would be updated).

I am using Manjaro (Arch-based, not a Debian-based Linux)

---

Can you confirm step 2 and step 4?