<<  >> (p.8)
    Author Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner  (Read 452742 times)

    • yuancraft
    Member
    **
    Offline Offline

    Activity: 63
    Merit: 10



    View Profile
    December 07, 2013, 09:34:12 AM
     #141
    Quote from: davecoin on December 07, 2013, 07:57:10 AM
    Is there a trick to getting the antminer to hold on to a reassigned static ip?

    I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs.  I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address.  I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either.  After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.

    Any ideas?



    you need to change you LAN before change the WAN

    LAN tab change to DHCP hit switch > save&apply .  wait a bit

    then back to WAN tab change the ip that u want > save&apply

  • sushi (OP)
    Full Member
    ***
    Offline Offline

    Activity: 238
    Merit: 100

    ASIC Myth Buster


    View Profile
    December 07, 2013, 02:25:14 PM
     #142
    I have seen this caused by the defective PSU not getting enough nice to the blades both or one of them.  also seen this error associated with the error on time server setting or the PSU needing the base charge...

    Error log associated with the cgminer status would be greatly appreciated!

    If it's mining in the Wi-Fi mode already, the PSU may not be the one but could be the other

    Sometimes, if it hangs, I noticed by hitting save the. Bit save and apply worked on time to time but not 100>.





    Quote from: davecoin on December 07, 2013, 07:57:10 AM
    Is there a trick to getting the antminer to hold on to a reassigned static ip?

    I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs.  I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address.  I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either.  After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.

    Any ideas?
    >>> PM me for New ASIC Miner's Info.  We will go check it out <<<
    FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P

  • davecoin
    Hero Member
    *****
    Offline Offline

    Activity: 816
    Merit: 1000


    View Profile
    December 07, 2013, 05:53:41 PM
    Last edit: December 07, 2013, 06:06:25 PM by davecoin
     #143
    Quote from: yuancraft on December 07, 2013, 09:34:12 AM
    Quote from: davecoin on December 07, 2013, 07:57:10 AM
    Is there a trick to getting the antminer to hold on to a reassigned static ip?

    I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs.  I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address.  I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either.  After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.

    Any ideas?



    you need to change you LAN before change the WAN

    LAN tab change to DHCP hit switch > save&apply .  wait a bit

    then back to WAN tab change the ip that u want > save&apply



    My LAN setting is DHCP Client by default.  If we are to assign a static ip should this be changed to "Static address"?

    The problem occurs when it tries to save changes.  I've tried hitting save, then applying the changes later before giving the miner a reboot, and it still hangs.

    This isn't a huge problem right now, as it's mining okay on wifi, but I'd still like to move it to the garage and give it a hard wired connection.

  • madpoet
    Sr. Member
    ****
    Offline Offline

    Activity: 448
    Merit: 250


    View Profile
    December 07, 2013, 05:59:08 PM
     #144
    LAN should ALWAYS be DHCP.  WAN should be static.

  • sushi (OP)
    Full Member
    ***
    Offline Offline

    Activity: 238
    Merit: 100

    ASIC Myth Buster


    View Profile
    December 07, 2013, 09:50:01 PM
     #145
    When there is nothing wrong with the system, you can change static ip and it will stay even you reboot.  But please pay attention where it gets stuck.  As soon as you hit save and apply, you will see little status thing will show up toward the top. Does it hang where it said applying changes to cgminer?

    When you see that, there is a setting issue with your AntMiner. Could be the wrong config data and could be not enough power going in, even it powers on, or could be the PSU problem and so on. 

    If it's mining in wifi no problem, my guess is in the config setting somewhere
    >>> PM me for New ASIC Miner's Info.  We will go check it out <<<
    FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P

  • Xer0
    Hero Member
    *****
    Offline Offline

    Activity: 826
    Merit: 1000


    °^°


    View Profile
    December 07, 2013, 10:01:41 PM
     #146
    i added a second fan, Scithe Grand Flex PWM with 96.8 cfm

    but the first blade is now hotter then before

    44/46 now - previous 42/46

  • klondike_bar
    Legendary
    *
    Offline Offline

    Activity: 2156
    Merit: 1005

    ASIC Wannabe


    View Profile
    December 07, 2013, 11:03:41 PM
     #147
    Quote from: mikep2012 on December 07, 2013, 07:23:35 AM
    and what is the meaning of this discoloration - working chip temperature is high and caused it? or maybe this issue is because quality of that painting might be not the best?
    asking because i've noticed this thing from the moment i've received my Ant's.
    thank you,

    my impresion was that the discolouration is just that the chips were poorly stamped/printed with the logo, and not an effect of operational heat - but i could be wrong
    24" PCI-E cables with 16AWG wires and stripped ends - great for server PSU mods, best prices https://bt.irlbtc.com/view/563461
    No longer a wannabe - now an ASIC owner!

  • AlexeyK
    Full Member
    ***
    Offline Offline

    Activity: 182
    Merit: 100


    View Profile
    December 08, 2013, 02:44:02 PM
     #148
    i got mine from GB , hashing now

    thanks for Bitmain and especially for Sushi

     
    if you think that i deserve it
    185h9KXxW2Efx6ynFM61ydUKsRNaVWUobs
    or GLC -  GQjVzfk3k8gb3Cy65mBUf4ADkNNTRHgsx8

  • warhawk187
    Sr. Member
    ****
    Offline Offline

    Activity: 327
    Merit: 250



    View Profile
    December 09, 2013, 05:15:41 AM
     #149
    I have been trying to SSH via WiFi on my local network, but I can't seem to connect. I reassigned my two miners to the same subnet as my router with end IPs being 253 and 254, but it never seems to connect. They are connected fine to my router and hashing on a pool, but I cannot SSH, or access the web interface wirelessly. Is there something I'm missing here?
    Need legit BTC fast? Check out my LocalBitcoins ad here. 100% perfect feedback. 100+ trades.

  • JohnC.
    Newbie
    *
    Offline Offline

    Activity: 30
    Merit: 0


    View Profile
    December 09, 2013, 09:45:30 AM
    Last edit: December 09, 2013, 10:04:47 AM by JohnC.
     #150
    @dropt Thanks for the info. I don't see any discoloration on my chips, but my inductors where really hot when i touched them.(not really scientific but i don't have the right equipment) So i placed some heatsinks on the inductors since that piece of the board doesn't seem to directly benefit from the stock lower heatsink, hopefully lowering the inductor heat will also benefit the voltage regulator since their close to each other. I also noticed temp difference(~4C) between the boards so i've aimed an extra fan to board 1 witch caused the stock fan to drop in speed and neutralized the temp difference between the boards. atm i'm getting about ~2% HW errors, is that acceptable?

    @warhawk187 i've run into sort of the same problem Sad
    When the miner is hooked up to the ethernet cable i can connect via the wifi ip-address(ssh&webinterface) to my miner, that works perfectly.
    As soon as i remove the lan cable i can't connect anymore but the miner will keep mining, so it looks like some sort of firewall issue?

  • novymivo
    Sr. Member
    ****
    Offline Offline

    Activity: 266
    Merit: 250


    View Profile
    December 09, 2013, 10:16:00 AM
     #151
    What is the safe range of temperature for antminer ?
    What is the maximum speed of antminer fan ??
    kind regards
    1DP6hkRCNoxE15QFfyeqxRk1qu7gX4FzGS

  • miter_myles
    Hero Member
    *****
    Offline Offline

    Activity: 742
    Merit: 500



    View Profile
    December 09, 2013, 11:45:25 PM
     #152
    Wow.. fast shipping.. my ordered extenders aren't here yet...

    I seem to have quite a few of these.. think they came in the sapphire 7950 boxes I have...

    Any issues using two of these per blade? 



    Thanks
    BTC - 1D7g5395bs7idApTx1KTXrfDW7JUgzx6Z5
    LTC - LVFukQnCWUimBxZuXKqTVKy1L2Jb8kZasL

  • sushi (OP)
    Full Member
    ***
    Offline Offline

    Activity: 238
    Merit: 100

    ASIC Myth Buster


    View Profile
    December 10, 2013, 01:55:19 AM
     #153
    May be 2 but 3 recommended!!!


    Quote from: miter_myles on December 09, 2013, 11:45:25 PM
    Wow.. fast shipping.. my ordered extenders aren't here yet...

    I seem to have quite a few of these.. think they came in the sapphire 7950 boxes I have...

    Any issues using two of these per blade? 



    Thanks
    >>> PM me for New ASIC Miner's Info.  We will go check it out <<<
    FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P

  • arorts
    Sr. Member
    ****
    Offline Offline

    Activity: 408
    Merit: 250


    View Profile
    December 10, 2013, 02:15:01 AM
     #154
    Can someone please explain how to configure the miner in Wi-Fi mode?  It's poorly documented.

    I can't get to do so. It won't even find my wifi router. :-(


    Thanks,
    arorts

  • arorts
    Sr. Member
    ****
    Offline Offline

    Activity: 408
    Merit: 250


    View Profile
    December 10, 2013, 02:25:26 AM
     #155
    Quote from: madpoet on December 07, 2013, 05:59:08 PM
    LAN should ALWAYS be DHCP.  WAN should be static.

    Oh, crap. I set WAN to DHCP and now I can't access the miner. Any advice?

  • madpoet
    Sr. Member
    ****
    Offline Offline

    Activity: 448
    Merit: 250


    View Profile
    December 10, 2013, 03:06:16 AM
     #156
    Short the pins Sad

  • sushi (OP)
    Full Member
    ***
    Offline Offline

    Activity: 238
    Merit: 100

    ASIC Myth Buster


    View Profile
    December 10, 2013, 03:19:25 AM
     #157
    RESET

    Quote from: arorts on December 10, 2013, 02:25:26 AM
    Quote from: madpoet on December 07, 2013, 05:59:08 PM
    LAN should ALWAYS be DHCP.  WAN should be static.

    Oh, crap. I set WAN to DHCP and now I can't access the miner. Any advice?
    >>> PM me for New ASIC Miner's Info.  We will go check it out <<<
    FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P

  • miter_myles
    Hero Member
    *****
    Offline Offline

    Activity: 742
    Merit: 500



    View Profile
    December 10, 2013, 03:44:12 AM
     #158
    Alright - up and running - however I am getting that "hang" on saving cgminer settings..

    How the hell do I modify what the PDF states?  Pretty much zero Linux know-how here
    BTC - 1D7g5395bs7idApTx1KTXrfDW7JUgzx6Z5
    LTC - LVFukQnCWUimBxZuXKqTVKy1L2Jb8kZasL

  • davecoin
    Hero Member
    *****
    Offline Offline

    Activity: 816
    Merit: 1000


    View Profile
    December 10, 2013, 04:27:36 AM
     #159
    ssh into the miner and use vi (a linux text editor) to modify the file. Instructions are in the guide here by user goxed:

    https://bt.irlbtc.com/view/348327.0

  • miter_myles
    Hero Member
    *****
    Offline Offline

    Activity: 742
    Merit: 500



    View Profile
    December 10, 2013, 05:03:59 AM
    Last edit: December 10, 2013, 05:41:01 AM by miter_myles
     #160
    Quote from: davecoin on December 10, 2013, 04:27:36 AM
    ssh into the miner and use vi (a linux text editor) to modify the file. Instructions are in the guide here by user goxed:

    https://bt.irlbtc.com/view/348327.0

    That helped!  thanks!

    Now - I can save my pool info successfully... reboot, nothing going on... le sigh... killawatt says 100-110 watts of something is goin on.. nothing populated under the miner status page..  

    thoughts?

    NM - good to go..
    BTC - 1D7g5395bs7idApTx1KTXrfDW7JUgzx6Z5
    LTC - LVFukQnCWUimBxZuXKqTVKy1L2Jb8kZasL
    Pages: « 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 ... 163 »
      Print  
Page 7
Viewing Page: 8

IRLBTC™ © 2025 IRLBTC.com