Mine came in today. Wow that was fast. Thank you! High quality stuff, well packed.

Wanted to tell Sidehack that one of the reasons for my ordering was the 'made in usa' commitment mentioned earlier in the other thread. Thank you for that.

Lastly... So ah.. any documentation? I went back through all the side-hack posts and so no explicit mention of any, and checked the website as well. I did see the line drawing for dimensions, but nothing electrical. Was hoping for a diagram of what pin is what at least. Im competant enough to make use of all the functionality described, but not completely comfortable just figuring it out from scratch if its not necessary.

Thanks!

Edit:

Ok I did now notice that partially obscured under the pin connector are tiny little letters indicating what the pins do. A diagram about the blue switch box, the potentiometer, and the pins would be nicer to have though.

What I can make out is this
GND COM GND xxx xxx xxx SHR? xxx EON POK
                                           FAN

Wow I looked at that page so many times, and totally missed that link. Thank you for posting it. Exactly what i was looking for.

Edit: after noting that the link was added per the note below.

Even better!
I was kinda worried about my having missed that so often.

Also if you email asking for stuff, go ahead and tell us where you are (country and whatnot) because we can't invoice you an amount without verifying the shipping.

As of now we have around two dozen boards left in stock, and once they're gone it'll be next week sometime before we have more.

I'm going to spend time this week hopefully finishing up and ironing out details for DPS-2000BB and DPS-800GBA boards. I've had a lot of interest in DPS-2000BB boards lately so that's high priority. DPS-800GBA boards I could basically finish now, if we didn't want to implement load-balancing, but that's a totally handy feature.

Anything is possible, sure, but none of what you just said is recommended. The boards' 3.3V and 5V lines are auxilary, rated for 2A, so if you can guarantee your ATX supply will pull less than 2A you might not smoke something. The aux power lines are there to power external controllers for handling multiple supplies, or things like Raspberry PI that are packaged with some miners.

The board is built to work with one power supply. There are probably ways to use only 1 breakout board for two supplies, but that defeats the purpose of the breakout board, probably won't be terribly safe or terribly reliable, and soldering stuff to the board will probably void any implied or actual warranties.

Good to hear, sir. Thanks, until my minions are fully trained on acceptable standards I've been going over every board for mechanical, functional and cosmetic to make sure everything was top-notch, so I like hearing what you just said.

Also I currently have 5 AntMiner S1 on 400MHz overclock, load-balanced across 3 of these boards with zero issues. Been running about five hours so far. So that's good.

We ran 2 sets of 2 OCed to 400 for 2 weeks on 1 PSU/board without a single issue. Pulling 880w at the wall  @120v

I think the price is great for an industrial spec psu and far better than some POS bronze ATX PSU. These are more efficient, extremely cheap to replace and have a much better foot print. Warranty is great until you have to file an RMA claim and be without gear for 4-6 weeks, pack that shit up with every bit and piece it came with and ship it at your expense. After all this hassle is the RMA even worth it! I would rather save the bones, get a better product and hot swap if ever required.

You pay for the cost of that warranty upfront in that ATX PSU. In most cases you wont even use it, I would rather gamble and bite the bullet if I have to. Warranties make the manufacturer money, not you. If the benefit was in favor of the consumer they wouldn't offer it!

Sweet! I estimated a pair of 400MHz Ants would be basically 99% capacity for the supply, so 2 weeks uptime at that load is pretty dern sexy. The only one of these supplies that's laid over on me ran a pair of custom-overclocked Cubes for a week basically with the fan disabled.



These will run 100-240VAC
Email sales@gekkoscience for pricing/shipping estimates. 3 in parallel to power 5 Ants works, I'm doing it right now.
The PSUs don't get terribly hot; if they're too warm just turn the fan up. They have internal fans and the board has a speed adjust knob.

Just checked out the link and am still a little unclear on the wiring. When connecting 12v and gnd do you need to bridge all 8 connections between the 2 psu's? Then do you fit the pci-e cables into the same terminal blocks.

If someone could post an actual picture it would be greatly appreciated! I'm trying to figure out how to link 3.

sidehack, I PM and emailed you to buy, but no response yet  



I think this should be how you connect two together for load balancing or simultaneous start up (I'm sure sidehack correct me if I'm wrong):