GrapeApe: Easily, with a little room for OC'ing and the 1300's are quiet/silent.

CG: Those Prisma's are sexy beautiful. Can't wait to get mine in house. Did ya' get my email?

Thanks for all the responses. That's good to hear because I bought 3 of those 1300's.

I posted this in friedcats thread I thought I would ask here as well.

Batch 1 has been dropped off at the post office. I hope to have an update on remaining batches soon.

Cheers!

Can you show what this is connected to? Ethernet controller are you using RPI?

Any batch 6 available for order

I now have tracking for batch 2.

I've added final shipping dimensions and weight to the second post. Also, after a bit of head scratching, I've figured out that AM reversed the order of the 5 bit switch in comparison to the Tube. Adding to that the limitation of a 4 bit configurable address space.

Here's what you need to know:

1) Each physical board has two addresses in a 5 bit address space. Only 4 of those bits are configurable. Boards 01-16 are paired with logical boards 17-32, starting with the first switch configuration(0000). This results in the first physical board having an address of 01 and 17
2) Boards must be chained in incremental order. (Example: 01:17,02:18,03:19,04:20,05:21...)
3) The least significant bit is reversed from the tube, with the tube's last switch,"5", being the least significant bit and the Prisma's first switch ,"1", being the least significant bit. Off and on still refer to 0 and 1 respectively.

Warning: Leave Switch 5 alone! If you set it on for any board, the controller will not see any boards in your chain.


Example switch configuration. ( "X" is OFF, "O" is on)

Board 1: (01:17)
Switch :  1  2  3  4  5
Setting:  X  X  X  X  X

Board 2: (02:18)
Switch :  1  2  3  4  5
Setting:  O  X  X  X  X

Board 3: (03:19)
Switch :  1  2  3  4  5
Setting:  X  O  X  X  X

Board 4: (04:20)
Switch :  1  2  3  4  5
Setting:  O  O  X  X  X

Board 5: (05:21)
Switch :  1  2  3  4  5
Setting:  X  X  O  X  X

Board 6: (06:22)
Switch :  1  2  3  4  5
Setting:  O  X  O  X  X

Board 7: (07:23)
Switch :  1  2  3  4  5
Setting:  X  O  O  X  X

Board 8: (08:24)
Switch :  1  2  3  4  5
Setting:  O  O  O  X  X

Board 9: (09:25)
Switch :  1  2  3  4  5
Setting:  X  X  X  O  X

Board 10: (10:26)
Switch :  1  2  3  4  5
Setting:  O  X  X  O  X

Board 11: (11:27)
Switch :  1  2  3  4  5
Setting:  X  O  X  O  X

Board 12: (12:28)
Switch :  1  2  3  4  5
Setting:  O  O  X  O  X

Board 13: (13:29)
Switch :  1  2  3  4  5
Setting:  X  X  O  O  X

Board 14: (14:30)
Switch :  1  2  3  4  5
Setting:  O  X  O  O  X

Board 15: (15:31)
Switch :  1  2  3  4  5
Setting:  X  O  O  O  X

Board 16: (16:32)
Switch :  1  2  3  4  5
Setting:  O  O  O  O  X

I ordered two on batch 4. Do I need to order those uart to usb adapters that GrapeApe bought? I know starting at batch 4 they came with something I am guessing it was these adapters wasn't it? Im also curious how these are going to work on a RPI, I have the B+ model and now im getting nervous as shipping is getting closer. Time to get the latest minera image on that B+ and give it a shot. They do look nice, cant wait to get my hands on them. Thanks CrazyGuy

Thanks GrapeApe. I just want to be sure I have everything ready when they show up. Now about them running on a B+ PI is my only concern. And of course power. Thanks again

If these are controlled the same as the Tubes - which seems likely since they run on Tube controllers as well - you would need a USB-UART adapter's RX, TX and GND lines. I think it's a 3V3 signal voltage. But the actual protocol was a nine-data-bits, I think no parity, at 460800 baud, which isn't a mode that many converters support. I'd be surprised if the one he bought would do it, based on what Novak turned up while working on RPi support before AM released their cgminer stuff.