i hope DEV you make tutorial
how to have connection in the wallet how to add nodes and how to run masternode
i think there a lot who want to run masternode
but didnt know how and experience diffirent problem
there a lot want to buy in the market but didnt know where they can use it
maybe thats why the buy support getting weaker and weaker
Hi!
Good questions hope these answers can help
1. How to connect wallet & add nodes?In win QT go to Tools -> Information -> Console and write
addnode 104.207.138.176 add
addnode 144.76.239.66 add
addnode 54.187.214.128 add
Here is a list with connected peers
http://www.blocktree.io/peers/ICASH/2. How to run a masternode?Here is a guide that BanzaiBTC started, do you have any questions or problems, just ask and I'll will gladly assist.
You need 100,000 ICASH instead of 1000 ICASHSetting up a masternode - WindowsWe will be using your home computer for this
nothing fancy
Create a new .txt file, we need to copy/paste a few codes/addresses
Start with a new wallet (0 balance) but first back up your old wallet.dat if you have coins in it
Open te QT, and make sure you have your firewall accepting connections from the Icash QT
Let it sync up
After you synced, go to Tools=>Debugconsole=>Console
Then typ :
masternode genkey Press enter
You will see a large code, copy this code to the .txt file for now. We need this code later on when we are setting up a new Icash.conf file
Go back to your Wallet=>Tools=>Debugconsole=>Console
Then typ :
getaccountaddress 0This will give you a new Icash address. Copy this address to the .txt file for now. We need this address later on to sent EXACTLY 1000 Icash to it (more or less will not work!) so you are able to be a masternode
Next you need to encrypt your wallet! Make sure you think of a strong password!
Settings=>encrypt wallet
After doing that your wallet needs to restart.
Alright, It is time to sent those 1000 ICASH to the "address 0" you copy/pasted in the .txt file. make sure it is EXACTLY 1000!!
If you have coins in your backed up wallet. Close down the Icash QT and just switch your wallet.dat with the back up wallet.dat (the one with your coins in it
) make sure you dont remove or lose the other "masternode" one, just put it away somewhere else for a sec.
Restart the Icash QT, Let it load, and you should see you have balance again from your backup wallet.
Send 1000 coins to the Icash address we put in the .txt file earlier. Let it fully confirm in the blockchain.
Close the Icash QT and swap the wallet.dat files again. You will now need the masternode wallet.dat file again.
Next, we need to make a new .conf file
maxconnections=100
rpcuser=yourusername
rpcpassword=yourpassword
rpcallowip=*
rpcport=5555
gen=0
listen=0
server=1
daemon=1
reservebalance=9999999
logtimestamps=1
masternodeaddr=YOURIPADDRESS:5555
masternode=1
masternodeprivkey=YOUR GENERATED PRIV KEY
addnode=104.238.165.95
addnode=104.207.138.176
Change username/password
Replace
YOURIPADDRESS with your ip address
Replace the
YOUR GENERATED PRIV KEY with the one you copy/pasted in the .txt file
Save as Icash.conf (we all know where to put this right?)
Open the Icash QT
Go to Tools=>Debugconsole=>Console
Typ
masternode start walletpassword
Then typ
masternode listIf you did everything right, and followed this guide step by step you should see you ip addres in the list with :1 behind it... then it is all set! Leave your wallet open though
I think ive got it right.. What do you think dev?
Icash address : iETMTZ42Xo1wAeFosGMdHqcp4hnW5VQh9H
