Thanks Christian for posting that, I do basically the same stuff using the .bat files. One suggestion you may want to add is using '--incognito' on the chrome startup command, as it will avoid any problems of Chrome trying to recover any open tabs if the system freezes or boots for other reasons (pulling the plug remotely, etc...). Shouldn't change the behavior of the 3d .SWF at all as far as the mining goes.

I am going to try out the SWF now and see if it helps me at all.

Thanks also.
Archive is updated... :-)

Same hashes@lower Watts.
You can also try if you can use that energy for
some more speed of the GPU.

"Amazing!
I'll have to give it a shot as soon as I get a 750 ti."
https://litecointalk.org/index.php?topic=16800.msg137703#msg137703


Why, Ivan... Why?

dwarfpool for fugue/groestl and hvc.1gh.com for heavy

I have only been mining Heavycoin so don't know much about the other two at this point, but I do know it takes 20-30 minutes sometimes for the cards to hit max speed, and I always minimize the windows and use the -q options to limit the amount of data trying to be written to those windows.

You probably know this, but you mentioned 6 cards, but you only have one card assigned to each config here. Maybe that is what you were just doing to test it out...

Edit: Saw your pic above, and do only see three cards... so maybe that is all you ordered. Nix that then if that is the case. My cards always come up 0,1,2,3 though, so that seems a little odd to me... but I am no expert in how the PCI-e slots recognize things.

No i only have 3 750Ti's
One algo per card.

I know i can launch it twice per card to get extra performance but if their not mining right i dont need that yet. The hvc miner is close to 99% usage

The other 2 sitting at around 50% usage so should easily handle 2 instances

Right now im going to minimal power over performance :-)
New psu, new cards, power usage of my entire system should be tiny.

My main rig with the 780 in is chilling out at 60W usage (watercooled). Then i have those 3 cards running. Should be pretty low power usage

I also have an issue with the fugue launch where it almost crashes, saying its mining at like 5gh/s constantly, similar to cudaminer if you run an invalid launch config? It happens randomly but ive seen it twice now in less then an hour

EDIT
Ok so fugue was crashing so much ive switched the card to mine hvc. Another thing i noticed is that if i shut off a ccminer instance by clicking the X instead of CTRL-C it crashes any open groestl or fugue miners (shows stupid hash's a second). Heavy coin stays untouched....

EDIT
Getting the crashing on groestl aswell now.
Just switched all 3 cards to heavycoin with the same launch config. And weirdly 2 cards run fine, another hardly gets any shares atall and cudaminer 3.0 and 3.5 both crash after a few minutes

EDIT
Device 2 which is the one that keeps crashing is now only mining at 3MH/s on heavy, and wont clock itself up anymore to mine properly?
other 2 750Ti's are running fine

EDIT
sorry for so many edits :-(
i just changed my heavycoin config to this
ccminer-v0.5\x86\ccminer35.exe -a heavy -q -d 1,2,3 -o stratum+tcp://hvcpool.1gh.com:5333 -u wallet -p VIP -v 512

getting better hash rates, 33MH/s in total
slower shares, ooo and ccminer keeps crashing? if i use compute 3.0 or 3.5
any advice?

I'm currently getting 963,000 Khash for 6x750Ti cards on that METH coin but pools are reporting 190,582,015 Khash. Not sure what's up with that or what is actually being counted.

I should have solo'd at launch since I was top of the hardcoreminers pool for the first 40min but their % jumped to 12,000 and never reported finding a block and then their pool went down

Someone said there might be something wrong with the blockchain for METH.  It's currently at %15,000 on okaypool now.

I only got .69 METH for my troubles.  Lame.