<<  >> (p.125)
    Author Topic: [Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner  (Read 452757 times)

    • AngusCanine
    Legendary
    *
    Offline Offline

    Activity: 1428
    Merit: 1001

    To weird to live To rare to die


    View Profile WWW
    March 31, 2014, 04:08:55 PM
     #2481
    these are the kernel logs
    Code:
    [/c[    0.000000] Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #2 Fri Feb 7 18:50:12 CST 2014
    [    0.000000] MyLoader: sysp=89697e3d, boardp=693d3833, parts=e47af0c4
    [    0.000000] bootconsole [early0] enabled
    [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
    [    0.000000] SoC: Atheros AR9330 rev 1
    [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
    [    0.000000] Determined physical RAM map:
    [    0.000000]  memory: 04000000 @ 00000000 (usable)
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
    [    0.000000] On node 0 totalpages: 16384
    [    0.000000] free_area_init_node: node 0, pgdat 803005b0, node_mem_map 81000000
    [    0.000000]   Normal zone: 128 pages used for memmap
    [    0.000000]   Normal zone: 0 pages reserved
    [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
    [    0.000000] pcpu-alloc: [0] 0
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
    [    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
    [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
    [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Writing ErrCtl register=00000000
    [    0.000000] Readback ErrCtl register=00000000
    [    0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
    [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    [    0.000000] NR_IRQS:51
    [    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
    [    0.080000] pid_max: default: 32768 minimum: 301
    [    0.080000] Mount-cache hash table entries: 512
    [    0.090000] NET: Registered protocol family 16
    [    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
    [    0.550000] bio: create slab <bio-0> at 0
    [    0.560000] Switching to clocksource MIPS
    [    0.560000] NET: Registered protocol family 2
    [    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
    [    0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
    [    0.570000] TCP: Hash tables configured (established 512 bind 512)
    [    0.580000] TCP: reno registered
    [    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
    [    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    [    0.600000] NET: Registered protocol family 1
    [    0.600000] PCI: CLS 0 bytes, default 32
    [    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
    [    0.630000] msgmni has been set to 119
    [    0.640000] io scheduler noop registered
    [    0.640000] io scheduler deadline registered (default)
    [    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
    [    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
    [    0.660000] console [ttyATH0] enabled, bootconsole disabled
    [    0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
    [    0.680000] m25p80 spi0.0: found mx25l6405d, expected m25p80
    [    0.680000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
    [    0.690000] 5 tp-link partitions found on MTD device spi0.0
    [    0.690000] Creating 5 MTD partitions on "spi0.0":
    [    0.700000] 0x000000000000-0x000000020000 : "u-boot"
    [    0.700000] 0x000000020000-0x000000117d84 : "kernel"
    [    0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    [    0.720000] 0x000000117d84-0x0000007f0000 : "rootfs"
    [    0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    [    0.740000] mtd: partition "rootfs" set to be root filesystem
    [    0.740000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
    [    0.750000] 0x000000370000-0x0000007f0000 : "rootfs_data"
    [    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
    [    0.770000] 0x0000007f0000-0x000000800000 : "art"
    [    0.790000] libphy: ag71xx_mdio: probed
    [    0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
    [    1.340000] eth0: Found an AR7240/AR9330 built-in switch
    [    2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
    [    2.930000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
    [    2.940000] TCP: cubic registered
    [    2.940000] NET: Registered protocol family 17
    [    2.950000] 8021q: 802.1Q VLAN Support v1.8
    [    2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
    [    2.970000] Freeing unused kernel memory: 232K (80316000 - 80350000)
    [    5.800000] usbcore: registered new interface driver usbfs
    [    5.800000] usbcore: registered new interface driver hub
    [    5.810000] usbcore: registered new device driver usb
    [    5.810000] usbcore: registered new interface driver bitmain
    [    5.820000] hash ok
    [    5.820000] hashtest OK
    [    5.820000] bitmain-asic: success to register device
    [    5.830000] usbcore: registered new interface driver bitmainbl
    [    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    5.850000] ehci-platform: EHCI generic platform driver
    [    5.850000] ehci-platform ehci-platform: EHCI Host Controller
    [    5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
    [    5.870000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
    [    5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
    [    5.890000] hub 1-0:1.0: USB hub found
    [    5.890000] hub 1-0:1.0: 1 port detected
    [    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
    [    6.380000] hub 1-1:1.0: USB hub found
    [    6.380000] hub 1-1:1.0: 2 ports detected
    [   10.580000] jffs2: notice: (324) jffs2_build_xattr_subsystem: complete building xattr subsystem, 41 of xdatum (0 unchecked, 40 orphan) and 142 of xref (0 dead, 127 orphan) found.
    [   12.920000] hidraw: raw HID events driver (C) Jiri Kosina
    [   12.920000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
    [   12.930000] Backport generated by backports.git backports-20130617-4-ge3220f5
    [   12.940000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
    [   12.970000] usbcore: registered new interface driver usbhid
    [   12.970000] usbhid: USB HID core driver
    [   12.980000] usbcore: registered new interface driver usbserial
    [   12.990000] usbcore: registered new interface driver usbserial_generic
    [   12.990000] usbserial: USB Serial support registered for generic
    [   13.020000] xt_time: kernel timezone is -0000
    [   13.060000] cfg80211: Calling CRDA to update world regulatory domain
    [   13.060000] cfg80211: World regulatory domain updated:
    [   13.070000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [   13.080000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.080000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   13.090000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   13.100000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.110000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
    [   13.250000] ath: EEPROM regdomain: 0x0
    [   13.250000] ath: EEPROM indicates default country code should be used
    [   13.250000] ath: doing EEPROM country->regdmn map search
    [   13.250000] ath: country maps to regdmn code: 0x3a
    [   13.250000] ath: Country alpha2 being used: US
    [   13.250000] ath: Regpair used: 0x3a
    [   13.260000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    [   13.270000] cfg80211: Calling CRDA for country: US
    [   13.270000] cfg80211: Regulatory domain changed to country: US
    [   13.280000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [   13.290000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
    [   13.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
    [   13.300000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.310000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.320000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   13.330000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
    [   13.340000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
    [   17.950000] device eth0 entered promiscuous mode
    [   20.100000] eth1: link up (100Mbps/Full duplex)
    ode]

  • skyzalimit
    Newbie
    *
    Offline Offline

    Activity: 10
    Merit: 0


    View Profile
    March 31, 2014, 04:40:24 PM
     #2482
    Quote from: sushi on November 25, 2013, 09:43:47 AM
    Power wise, as long as your computer's ATX or Server's power supply (PSU) supports it and the lines are +12V, you can use any of them.

    Best way would be not chop up the PSU's cables but use the extenders and then cut the extended portion, so you don't scarify your PSU.


     
    Quote from: Unacceptable on November 24, 2013, 11:47:55 PM
    6pin male:
    http://www.frozencpu.com/products/8620/ele-361/FrozenCPU_ConnectRight_6-pin_Male_PCI-Express_Power_Connector_-_Black.html?tl=g51c385s1005

    8pin male:
    http://www.frozencpu.com/products/8693/ele-369/PCI-E_8-pin_Male_Power_Connector_-_Black.html?tl=g51c383s1007

    Get the pins too & just crimp wires as long as you need em  Grin

    Im having problems with one of my AntMiner S1s  its only running at 120ghash and sometimes dipps down to 90
    Both boards seem to be running . Gettig good heat readings from all chips. Both green lights are blinking away.

    If anyone can help thatd be great

  • AngusCanine
    Legendary
    *
    Offline Offline

    Activity: 1428
    Merit: 1001

    To weird to live To rare to die


    View Profile WWW
    March 31, 2014, 04:46:58 PM
     #2483
    if I was to go to best buy what psu is sufficient power for 1 s1 im staring to think maybe the power supply is faulty, enough to turn it on but not enough to get a hashrate?

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 04:54:30 PM
     #2484
    Quote from: AngusCanine on March 31, 2014, 04:46:58 PM
    if I was to go to best buy what psu is sufficient power for 1 s1 im staring to think maybe the power supply is faulty, enough to turn it on but not enough to get a hashrate?

    I'd turn it off and remove power from the dependent side of the machine and see if the other side hashes.

  • Biodom
    Legendary
    *
    Offline Offline

    Activity: 4242
    Merit: 5308



    View Profile
    March 31, 2014, 07:27:29 PM
     #2485
    One of my ants shows a significant difference in hashing between what miner software is showing (191) and what eligius pool is showing (187) over the same timeframe (12hr). Is this a fee or something wackier?

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 07:48:04 PM
     #2486
    Quote from: Biodom on March 31, 2014, 07:27:29 PM
    One of my ants shows a significant difference in hashing between what miner software is showing (191) and what eligius pool is showing (187) over the same timeframe (12hr). Is this a fee or something wackier?

    Not sure how a fee lessens your hashrate and eligius has no fee anyway.

    You are comparing a true running 12hr avg to a "lifetime" avg (i.e. since the antminer was started).

    you are so close I'm pretty sure you are ok.

  • Raptor2213
    Full Member
    ***
    Offline Offline

    Activity: 210
    Merit: 100


    View Profile
    March 31, 2014, 08:41:39 PM
     #2487
    I'm having issues updating cgminer with Kano's firmware at https://github.com/kanoi/cgminer-binaries/tree/master/AntS1
    I run the following command in putty:
    Code:
    cdusr/bin/
    wget http://kano-kun.net/AntS1/cgminer-ants1-4.2.2a-7b8fb34
    chmod +x cgminer-ants1-4.2.2a-7b8fb34
    mv cgminer cgminer.original
    rm cgminer
    ln -s cgminer-ants1-4.2.2a-7b8fb34 cgminer

    I've saved and applied and even restarted the miner.  It uses disk space, but doesn't update the cgminer version past 3.12.0-1 (should be updating to 4.2.2a).
    Did something I say help you out?    BTC - 18oTipf66z8dbwTgRCiPjbdPmqEP7zuCFb

  • jedimstr
    Hero Member
    *****
    Offline Offline

    Activity: 798
    Merit: 1000



    View Profile
    March 31, 2014, 08:53:04 PM
     #2488
    Quote from: Raptor2213 on March 31, 2014, 08:41:39 PM
    I'm having issues updating cgminer with Kano's firmware at https://github.com/kanoi/cgminer-binaries/tree/master/AntS1
    I run the following command in putty:
    Code:
    cdusr/bin/
    wget http://kano-kun.net/AntS1/cgminer-ants1-4.2.2a-7b8fb34
    chmod +x cgminer-ants1-4.2.2a-7b8fb34
    mv cgminer cgminer.original
    rm cgminer
    ln -s cgminer-ants1-4.2.2a-7b8fb34 cgminer

    I've saved and applied and even restarted the miner.  It uses disk space, but doesn't update the cgminer version past 3.12.0-1 (should be updating to 4.2.2a).

    Are you seeing any error messages after executing each of those commands when you're logged into your S1's terminal?
    What exactly are you seeing?
    BTC Tips:12kQtnCzotLE6MNjKRtR5Cww843baahxq5

  • AngusCanine
    Legendary
    *
    Offline Offline

    Activity: 1428
    Merit: 1001

    To weird to live To rare to die


    View Profile WWW
    March 31, 2014, 08:58:14 PM
     #2489
    Quote from: RicRock on March 31, 2014, 04:54:30 PM
    Quote from: AngusCanine on March 31, 2014, 04:46:58 PM
    if I was to go to best buy what psu is sufficient power for 1 s1 im staring to think maybe the power supply is faulty, enough to turn it on but not enough to get a hashrate?

    I'd turn it off and remove power from the dependent side of the machine and see if the other side hashes.
    would I have to disconnect the 8 pin cable also connecting the two boards

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 09:05:28 PM
     #2490
    Quote from: AngusCanine on March 31, 2014, 08:58:14 PM
    Quote from: RicRock on March 31, 2014, 04:54:30 PM
    Quote from: AngusCanine on March 31, 2014, 04:46:58 PM
    if I was to go to best buy what psu is sufficient power for 1 s1 im staring to think maybe the power supply is faulty, enough to turn it on but not enough to get a hashrate?

    I'd turn it off and remove power from the dependent side of the machine and see if the other side hashes.
    would I have to disconnect the 8 pin cable also connecting the two boards

    Sure

  • f430
    Newbie
    *
    Offline Offline

    Activity: 9
    Merit: 0


    View Profile
    March 31, 2014, 09:09:56 PM
     #2491
    So what kind of btc are you guys cranking out with 1 ant at ~200Gh/s?
    Pool says my average is 187Gh/s which I am OK with
    I'm at 375MHz (400 gave two-three xxx on ASICS status so I turned it down a little bit)

    My BTC seems low compared to what I calculated before going into this crazy experiment called mining Cheesy
    Eyeballing 0.012 - 0.015 BTC day, haven't done an hourly calculation yet.

    Thanks for any feedback!

  • Raptor2213
    Full Member
    ***
    Offline Offline

    Activity: 210
    Merit: 100


    View Profile
    March 31, 2014, 09:11:58 PM
     #2492
    Quote from: jedimstr on March 31, 2014, 08:53:04 PM
    Quote from: Raptor2213 on March 31, 2014, 08:41:39 PM
    I'm having issues updating cgminer with Kano's firmware at https://github.com/kanoi/cgminer-binaries/tree/master/AntS1
    I run the following command in putty:
    Code:
    cdusr/bin/
    wget http://kano-kun.net/AntS1/cgminer-ants1-4.2.2a-7b8fb34
    chmod +x cgminer-ants1-4.2.2a-7b8fb34
    mv cgminer cgminer.original
    rm cgminer
    ln -s cgminer-ants1-4.2.2a-7b8fb34 cgminer

    I've saved and applied and even restarted the miner.  It uses disk space, but doesn't update the cgminer version past 3.12.0-1 (should be updating to 4.2.2a).

    Are you seeing any error messages after executing each of those commands when you're logged into your S1's terminal?
    What exactly are you seeing?

    Code:
    alias: -l not found
    root@antMiner:~# cdusr/bin/
    root@antMiner:/usr/bin# wget http://kano-kun.net/AntS1/cgminer-ants1-4.2.2a-7b8fb34
    Connecting to kano-kun.net (198.100.107.213:80)
    cgminer-ants1-4.2.2a 100% |*******************************|   348k  0:00:00 ETA
    root@antMiner:/usr/bin# chmod +x cgminer-ants1-4.2.2a-7b8fb34
    root@antMiner:/usr/bin# mv cgminer cgminer.original
    root@antMiner:/usr/bin# rm cgminer
    rm: can't remove 'cgminer': No such file or directory
    root@antMiner:/usr/bin# ln -s cgminer-ants1-4.2.2a-7b8fb34 cgminer
    root@antMiner:/usr/bin#
    root@antMiner:/usr/bin#
    No errors (except for the rm command, which isn't needed for first-time-use).
    Did something I say help you out?    BTC - 18oTipf66z8dbwTgRCiPjbdPmqEP7zuCFb

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 09:41:34 PM
     #2493
    Quote from: Raptor2213 on March 31, 2014, 09:11:58 PM

    No errors (except for the rm command, which isn't needed for first-time-use).


    rm not needed for anytime use since you are doing a move command and not copy.

    Have you rebooted?

    What does cgminer -V show?

  • Raptor2213
    Full Member
    ***
    Offline Offline

    Activity: 210
    Merit: 100


    View Profile
    March 31, 2014, 10:10:34 PM
     #2494
    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    Quote from: Raptor2213 on March 31, 2014, 09:11:58 PM
    No errors (except for the rm command, which isn't needed for first-time-use).
    rm not needed for anytime use since you are doing a move command and not copy.
    I'm aware of that.  It's just a catch-all script.

    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    Have you rebooted?
    Yes, I mentioned this in my OP.

    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    What does cgminer -V show?
    3.12.0
    Did something I say help you out?    BTC - 18oTipf66z8dbwTgRCiPjbdPmqEP7zuCFb

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 10:32:25 PM
     #2495
    Quote from: Raptor2213 on March 31, 2014, 10:10:34 PM
    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    Quote from: Raptor2213 on March 31, 2014, 09:11:58 PM
    No errors (except for the rm command, which isn't needed for first-time-use).
    rm not needed for anytime use since you are doing a move command and not copy.
    I'm aware of that.  It's just a catch-all script.

    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    Have you rebooted?
    Yes, I mentioned this in my OP.

    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    What does cgminer -V show?
    3.12.0

    You said you restarted the miner which I assumed it would be restarting cgminer.

    what does
    which cgminer
    show?

    Should obv be the one inusr/bin

    Would be weird to have multiples.

  • Biodom
    Legendary
    *
    Offline Offline

    Activity: 4242
    Merit: 5308



    View Profile
    March 31, 2014, 10:35:12 PM
     #2496
    Quote from: f430 on March 31, 2014, 09:09:56 PM
    So what kind of btc are you guys cranking out with 1 ant at ~200Gh/s?
    Pool says my average is 187Gh/s which I am OK with
    I'm at 375MHz (400 gave two-three xxx on ASICS status so I turned it down a little bit)

    My BTC seems low compared to what I calculated before going into this crazy experiment called mining Cheesy
    Eyeballing 0.012 - 0.015 BTC day, haven't done an hourly calculation yet.

    Thanks for any feedback!

    Don't eyeball-eligius gives precise statistics. At 187 it should be ~0.0184-0.0187.

  • klondike_bar
    Legendary
    *
    Offline Offline

    Activity: 2156
    Merit: 1005

    ASIC Wannabe


    View Profile
    March 31, 2014, 10:47:43 PM
     #2497
    Quote from: AngusCanine on March 31, 2014, 04:01:52 PM
    the system logs of my s1 that's has zero hashrate


    Code:
    [/Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.660000] console [ttyATH0] enabled, bootconsole disabled
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
    Wed Dec 31 19:00:11 1969 kern.warn kernel: [    0.680000] m25p80 spi0.0: found mx25l6405d, expected m25p80
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.680000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.690000] 5 tp-link partitions found on MTD device spi0.0
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.690000] Creating 5 MTD partitions on "spi0.0":
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.700000] 0x000000000000-0x000000020000 : "u-boot"
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.700000] 0x000000020000-0x000000117d84 : "kernel"
    Wed Dec 31 19:00:11 1969 kern.warn kernel: [    0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.720000] 0x000000117d84-0x0000007f0000 : "rootfs"
    Wed Dec 31 19:00:11 1969 kern.warn kernel: [    0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.740000] mtd: partition "rootfs" set to be root filesystem
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.740000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.750000] 0x000000370000-0x0000007f0000 : "rootfs_data"
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [    0.770000] 0x0000007f0000-0x000000800000 : "art"
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.790000] libphy: ag71xx_mdio: probed
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    1.340000] eth0: Found an AR7240/AR9330 built-in switch
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.930000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.940000] TCP: cubic registered
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.940000] NET: Registered protocol family 17
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.950000] 8021q: 802.1Q VLAN Support v1.8
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    2.970000] Freeing unused kernel memory: 232K (80316000 - 80350000)
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.800000] usbcore: registered new interface driver usbfs
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.800000] usbcore: registered new interface driver hub
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.810000] usbcore: registered new device driver usb
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.810000] usbcore: registered new interface driver bitmain
    Wed Dec 31 19:00:11 1969 kern.warn kernel: [    5.820000] hash ok
    Wed Dec 31 19:00:11 1969 kern.warn kernel: [    5.820000] hashtest OK
    Wed Dec 31 19:00:11 1969 kern.err kernel: [    5.820000] bitmain-asic: success to register device
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.830000] usbcore: registered new interface driver bitmainbl
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.850000] ehci-platform: EHCI generic platform driver
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.850000] ehci-platform ehci-platform: EHCI Host Controller
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.870000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.890000] hub 1-0:1.0: USB hub found
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    5.890000] hub 1-0:1.0: 1 port detected
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    6.380000] hub 1-1:1.0: USB hub found
    Wed Dec 31 19:00:11 1969 kern.info kernel: [    6.380000] hub 1-1:1.0: 2 ports detected
    Wed Dec 31 19:00:11 1969 kern.notice kernel: [   10.580000] jffs2: notice: (324) jffs2_build_xattr_subsystem: complete building xattr subsystem, 41 of xdatum (0 unchecked, 40 orphan) and 142 of xref (0 dead, 127 orphan) found.
    Mon Mar 31 11:43:00 2014 daemon.info sysinit: Mon Mar 31 15:43:00 UTC 2014
    Mon Mar 31 11:43:00 2014 user.emerg syslog: kmodloader: loading kernel modules frometc/modules.d/**
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.920000] hidraw: raw HID events driver (C) Jiri Kosina
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.920000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.930000] Backport generated by backports.git backports-20130617-4-ge3220f5
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.940000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.970000] usbcore: registered new interface driver usbhid
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.970000] usbhid: USB HID core driver
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.980000] usbcore: registered new interface driver usbserial
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.990000] usbcore: registered new interface driver usbserial_generic
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   12.990000] usbserial: USB Serial support registered for generic
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.020000] xt_time: kernel timezone is -0000
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.060000] cfg80211: Calling CRDA to update world regulatory domain
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.060000] cfg80211: World regulatory domain updated:
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.070000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.080000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.080000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.090000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.100000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.110000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.120000] ip_tables: (C) 2000-2006 Netfilter Core Team
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: EEPROM regdomain: 0x0
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: EEPROM indicates default country code should be used
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: doing EEPROM country->regdmn map search
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: country maps to regdmn code: 0x3a
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: Country alpha2 being used: US
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.250000] ath: Regpair used: 0x3a
    Mon Mar 31 11:43:00 2014 kern.debug kernel: [   13.260000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.270000] cfg80211: Calling CRDA for country: US
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.270000] cfg80211: Regulatory domain changed to country: US
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.280000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.290000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.300000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.310000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.320000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.330000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
    Mon Mar 31 11:43:00 2014 kern.info kernel: [   13.340000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
    Mon Mar 31 11:43:00 2014 user.info syslog: ran 16 iterations
    Mon Mar 31 11:43:00 2014 daemon.info sysinit: kmod: ran 16 iterations
    Mon Mar 31 11:43:04 2014 cron.info crond[569]: crond: crond (busybox 1.19.4) started, log level 8
    Mon Mar 31 11:43:05 2014 daemon.notice netifd: Interface 'loopback' is now up
    Mon Mar 31 11:43:05 2014 kern.info kernel: [   17.950000] device eth0 entered promiscuous mode
    Mon Mar 31 11:43:05 2014 daemon.notice netifd: Interface 'wan' is now up
    Mon Mar 31 11:43:05 2014 authpriv.info dropbear[580]: Not backgrounding
    Mon Mar 31 11:43:05 2014 daemon.notice netifd: lan (617): udhcpc (v1.19.4) started
    Mon Mar 31 11:43:06 2014 daemon.notice netifd: lan (617): Sending discover...
    Mon Mar 31 11:43:06 2014 user.notice firewall: Reloading firewall due to ifup of wan (eth1)
    Mon Mar 31 11:43:07 2014 kern.info kernel: [   20.100000] eth1: link up (100Mbps/Full duplex)
    Mon Mar 31 11:43:07 2014 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
    Mon Mar 31 11:43:07 2014 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: started, version 2.66 cachesize 150
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: using local addresses only for domain lan
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: readingtmp/resolv.conf.auto
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: using nameserver 192.168.2.1#53
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: using local addresses only for domain lan
    Mon Mar 31 11:43:08 2014 daemon.info dnsmasq[689]: readetc/hosts - 1 addresses
    Mon Mar 31 11:43:08 2014 daemon.info sysinit:etc/config/miner_pic.hex
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: Unable to opendev/bitmainbl0: No such file or directory
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: pic update
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led WAN
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led WANL
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led LAN1
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led LAN2
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led LAN3
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led LAN4
    Mon Mar 31 11:43:08 2014 daemon.info sysinit: setting up led WLAN
    Mon Mar 31 11:43:09 2014 daemon.notice netifd: lan (617): Sending discover...
    Mon Mar 31 11:43:12 2014 daemon.notice netifd: lan (617): Sending discover...
    Mon Mar 31 11:43:12 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 206.186.121.125
    Mon Mar 31 11:43:12 2014 daemon.info sysinit: ntpd: sent query to 206.186.121.125
    Mon Mar 31 11:43:13 2014 daemon.info sysinit: ntpd: resolved peer 2.openwrt.pool.ntp.org to 206.108.0.131
    Mon Mar 31 11:43:13 2014 daemon.info sysinit: ntpd: sent query to 206.108.0.131
    Mon Mar 31 11:43:13 2014 daemon.info sysinit: ntpd: resolved peer 1.openwrt.pool.ntp.org to 67.215.197.151
    Mon Mar 31 11:43:13 2014 daemon.info sysinit: ntpd: sent query to 67.215.197.151
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 198.50.209.202
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: sent query to 198.50.209.202
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: reply from 206.186.121.125: reach 0x01 offset 62.000103 delay 2.299706 status 0x24 strat 2 refid 0x1896cb96 rootdelay 0.009018
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: reply from 206.108.0.131: reach 0x01 offset 62.559352 delay 1.177639 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: reply from 67.215.197.151: reach 0x01 offset 62.672879 delay 0.962987 status 0x24 strat 2 refid 0xd8ab7824 rootdelay 0.018143
    Mon Mar 31 11:43:14 2014 daemon.info sysinit: ntpd: reply from 198.50.209.202: reach 0x01 offset 63.135136 delay 0.040115 status 0x24 strat 3 refid 0x80643887 rootdelay 0.009461
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: sent query to 206.186.121.125
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: sent query to 206.108.0.131
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: sent query to 67.215.197.151
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: sent query to 198.50.209.202
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: reply from 206.186.121.125: reach 0x03 offset 63.133026 delay 0.033123 status 0x24 strat 2 refid 0x1896cb96 rootdelay 0.009018
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: reply from 206.108.0.131: reach 0x03 offset 63.132975 delay 0.033267 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: reply from 67.215.197.151: reach 0x03 offset 63.135321 delay 0.043926 status 0x24 strat 2 refid 0xd8ab7824 rootdelay 0.018143
    Mon Mar 31 11:43:15 2014 daemon.info sysinit: ntpd: reply from 198.50.209.202: reach 0x03 offset 63.137362 delay 0.044243 status 0x24 strat 3 refid 0x80643887 rootdelay 0.009461
    Mon Mar 31 11:43:16 2014 daemon.info sysinit: ntpd: sent query to 206.186.121.125
    Mon Mar 31 11:43:16 2014 daemon.info sysinit: ntpd: sent query to 67.215.197.151
    Mon Mar 31 11:43:17 2014 daemon.info sysinit: ntpd: reply from 206.186.121.125: reach 0x07 offset 63.132578 delay 0.032586 status 0x24 strat 2 refid 0x1896cb96 rootdelay 0.009018
    Mon Mar 31 11:43:17 2014 daemon.info sysinit: ntpd: reply from 67.215.197.151: reach 0x07 offset 63.134666 delay 0.041811 status 0x24 strat 2 refid 0xd8ab7824 rootdelay 0.018143
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: sent query to 206.186.121.125
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: sent query to 206.108.0.131
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: sent query to 67.215.197.151
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: sent query to 198.50.209.202
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: reply from 206.186.121.125: reach 0x0f offset 63.131501 delay 0.034086 status 0x24 strat 2 refid 0x1896cb96 rootdelay 0.009018
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: reply from 206.108.0.131: reach 0x07 offset 63.131927 delay 0.034293 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: reply from 198.50.209.202: reach 0x07 offset 63.137826 delay 0.042555 status 0x24 strat 3 refid 0x80643887 rootdelay 0.009461
    Mon Mar 31 11:43:18 2014 daemon.info sysinit: ntpd: reply from 67.215.197.151: reach 0x0f offset 63.134811 delay 0.044772 status 0x24 strat 2 refid 0xd8ab7824 rootdelay 0.018143
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: sent query to 206.186.121.125
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: sent query to 206.108.0.131
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: sent query to 67.215.197.151
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: sent query to 198.50.209.202
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: reply from 206.186.121.125: reach 0x1f offset 63.132505 delay 0.035210 status 0x24 strat 2 refid 0x1896cb96 rootdelay 0.009018
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: reply from 206.108.0.131: reach 0x0f offset 63.132456 delay 0.035414 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: reply from 198.50.209.202: reach 0x0f offset 63.136858 delay 0.041736 status 0x24 strat 3 refid 0x80643887 rootdelay 0.009461
    Mon Mar 31 11:43:19 2014 daemon.info sysinit: ntpd: reply from 67.215.197.151: reach 0x1f offset 63.135846 delay 0.043975 status 0x24 strat 2 refid 0xd8ab7824 rootdelay 0.018143
    Mon Mar 31 11:43:20 2014 daemon.info sysinit: ntpd: sent query to 206.108.0.131
    Mon Mar 31 11:43:20 2014 daemon.info sysinit: ntpd: sent query to 198.50.209.202
    Mon Mar 31 11:44:23 2014 daemon.info sysinit: ntpd: reply from 206.108.0.131: reach 0x1f offset 63.131849 delay 0.033145 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
    Mon Mar 31 11:44:23 2014 daemon.info sysinit: ntpd: setting clock to Mon Mar 31 11:44:23 EDT 2014 (offset 63.060448s)
    Mon Mar 31 11:44:23 2014 daemon.info sysinit: --bitmain-options 115200:32:8:40:350:4d81 -o http://btc.e-pool.net:8800 -O 1MWhaSUrp3Cd8PQYGr3YNyperSRVmYDad7:1234 --api-listen --api-network
    Mon Mar 31 11:44:23 2014 daemon.info sysinit: - init complete -
    Mon Mar 31 11:45:04 2014 cron.info crond[569]: crond: USER root pid 1046 cmdusr/bin/cgminer-monitor
    Mon Mar 31 11:48:01 2014 cron.info crond[569]: crond: USER root pid 1324 cmdusr/bin/cgminer-monitor
    Mon Mar 31 11:51:01 2014 cron.info crond[569]: crond: USER root pid 1371 cmdusr/bin/cgminer-monitor
    Mon Mar 31 11:54:01 2014 cron.info crond[569]: crond: USER root pid 1421 cmdusr/bin/cgminer-monitor
    Mon Mar 31 11:57:01 2014 cron.info crond[569]: crond: USER root pid 1583 cmdusr/bin/cgminer-monitor
    code]

    here is a similar (same?) issue with an avalon a few months back.  Your issue is definitely with the network or network settings, and not the actual function of the miner (other than settings) https://bt.irlbtc.com/view/416940.40

    post your network settings and if DHCP is disabled. It seems certainly a network settings issue and not with the pool settings
    24" PCI-E cables with 16AWG wires and stripped ends - great for server PSU mods, best prices https://bt.irlbtc.com/view/563461
    No longer a wannabe - now an ASIC owner!

  • Raptor2213
    Full Member
    ***
    Offline Offline

    Activity: 210
    Merit: 100


    View Profile
    March 31, 2014, 10:52:01 PM
     #2498
    Quote from: Raptor2213 on March 31, 2014, 10:10:34 PM
    Quote from: RicRock on March 31, 2014, 09:41:34 PM


    Quote from: RicRock on March 31, 2014, 09:41:34 PM
    What does cgminer -V show?
    3.12.0

    You said you restarted the miner which I assumed it would be restarting cgminer.

    what does
    which cgminer
    show?

    Should obv be the one inusr/bin

    Would be weird to have multiples.

    I don't understand the question.  When I typed cgminer -V like you asked, it returns cgminer version 3.12.0
    Did something I say help you out?    BTC - 18oTipf66z8dbwTgRCiPjbdPmqEP7zuCFb

  • RicRock
    Sr. Member
    ****
    Offline Offline

    Activity: 290
    Merit: 250



    View Profile
    March 31, 2014, 11:00:27 PM
     #2499
    Quote from: Raptor2213 on March 31, 2014, 10:52:01 PM

    I don't understand the question.  When I typed cgminer -V like you asked, it returns cgminer version 3.12.0



    Type in "which cgminer"

    without the quotes

    it should return

    /usr/bin/cgminer

  • Raptor2213
    Full Member
    ***
    Offline Offline

    Activity: 210
    Merit: 100


    View Profile
    March 31, 2014, 11:02:11 PM
     #2500
    Quote from: RicRock on March 31, 2014, 11:00:27 PM
    Quote from: Raptor2213 on March 31, 2014, 10:52:01 PM

    I don't understand the question.  When I typed cgminer -V like you asked, it returns cgminer version 3.12.0

    Type in "which cgminer" without the quotes it should return usr/bin/cgminer

    It does.
    Did something I say help you out?    BTC - 18oTipf66z8dbwTgRCiPjbdPmqEP7zuCFb
    Pages: « 1 ... 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 [125] 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 »
      Print  
Page 124
Viewing Page: 125

IRLBTC™ © 2025 IRLBTC.com