<<  >> (p.6)
    Author Topic: Blue Fury Support Thread.  (Read 89645 times)

    • colemab
    Newbie
    *
    Offline Offline

    Activity: 54
    Merit: 0



    View Profile
    November 05, 2013, 01:02:21 AM
     #101
    I installed 3 units when I received them on Saturday.  They are running on Win 7 64 bit with provided drivers and bundled bfgminer version 3.2.0.  

    They have been running fine at about 2.25 Gh/s until today.  One of the units just stopped working - the other two were still working.  So I tried to unplug the unit and plug it back in without any luck.  Moving to a different USB port didn't work either.  Trying to manually add the device in bfgminer didn't work either.

    I ended up locating the 'bad' unit by seeing which com port was added when it was unplugged and plugged back in.  Then I stopped bfgminer.  Then I uninstalled the device from the device manager and unplugged replugged the unit back in.   After the driver was automatically re-installed, I restarted bfgminer at it started back up running fine.

    I post this here in case someone else sees this problem and/or my unit dies later on.

  • LogicalUnit
    Sr. Member
    ****
    Offline Offline

    Activity: 299
    Merit: 250


    View Profile
    November 05, 2013, 02:21:27 AM
     #102
    I have been able to get Block Erupters working concurrently with Blue Fury ASICs on MinePeon with bfgminer 3.3.0



    Sadly, some of the ASICs become unstable when I try to daisy-chain more than 1 hub per usb port on the Pi. Only four Blue Fury units will fit on a DUB-H7 due to their large profile.

    Here's what I put in my Miner Startup Setting:

    #!/bin/bash
    sleep 10
    /usr/bin/screen -dmS mineropt/minepeon/bin/bfgminer -S ICA:/dev/ttyUSB0 -S ICA:/dev/ttyUSB1 -S ICA:/dev/ttyUSB2 -S ICA:/dev/ttyUSB3 -S ICA:/dev/ttyUSB4 -copt/minepeon/etc/miner.conf

    Note that I do not manually specify the Blue Fury units. Doing this caused MinePeon to crash when I plugged in a second hub.

  • crudpuppy
    Full Member
    ***
    Offline Offline

    Activity: 224
    Merit: 100



    View Profile
    November 05, 2013, 03:09:34 AM
     #103
    Ok,  so I just got my tracking number for mine and was looking here to see what works and wont doesn't.
    I'm running win7 64bit with bout 35 block erupters right now under cgminer 3.5.0 so what will work on this OS and with these devices using zadiag preferred so I don't have all those dynamic com ports to mess with.

    Looks like some got working in cgminer 3.7.0?
    ███████████████████████ ▀▄ Platio ▄▀ ███████████████████████
    [TELEGRAM]│Smart Banking Ecosystem for crypto, fiat and│[FACEBOOK]
    [TWITTER] │stocks, based on EOS blockchain technology │ [MEDIUM]

  • Beastlymac (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 630
    Merit: 501


    Miner Setup And Reviews. WASP Rep.


    View Profile
    November 05, 2013, 03:22:26 AM
     #104
    Quote from: crudpuppy on November 05, 2013, 03:09:34 AM
    Ok,  so I just got my tracking number for mine and was looking here to see what works and wont doesn't.
    I'm running win7 64bit with bout 35 block erupters right now under cgminer 3.5.0 so what will work on this OS and with these devices using zadiag preferred so I don't have all those dynamic com ports to mess with.

    Looks like some got working in cgminer 3.7.0?
    Yes go with cgminer 3.7.0
    Message me if you have any problems

  • nite423
    Newbie
    *
    Offline Offline

    Activity: 47
    Merit: 0



    View Profile
    November 05, 2013, 04:26:31 AM
     #105
    Finally got my five fury's rolling this morning, I'm running CGMiner 3.7.0 on Windows 7.

    After 12 hours running I have still yet to get a single hardware error, but the overall hash speeds have been a little disappointing.  I do have one miner that is pushing 2.4 Gh/s but then they go south from there.  Two are running around 2.2 Gh/s, one is clinging at 2.0 Gh/s and the slowest is chugging around 1.8 Gh/s. 

    I'm guessing that I (along with others) are just needing to wait for some tweaks (drivers/firmware/CG-BFG miner updates) to come along to help squeeze more out of these little monsters. 

  • Epinnoia
    Full Member
    ***
    Offline Offline

    Activity: 209
    Merit: 100


    View Profile
    November 05, 2013, 05:11:22 AM
    Last edit: November 05, 2013, 05:24:49 AM by Epinnoia
     #106
    Quote from: nite423 on November 05, 2013, 04:26:31 AM
    Finally got my five fury's rolling this morning, I'm running CGMiner 3.7.0 on Windows 7.

    3.7.0 is giving me 100Mh/sec LESS than 3.6.6 did, with lots of "GetResults took 1000ms but was 10ms" that were not there in 3.6.6.  Instead of 1.3 to 1.4 Gh/sec, it's getting 1.2 to 1.3 Gh/sec in 3.7.0.  So, for now, I am reverting back to the debug build that was made available a couple/few days ago of 3.6.6.  





    64bit Win7
    My first miner -> ATI 4550 (7.2 Mh/sec): 
    https://www.facebook.com/groups/cryptospeculators/

  • mogrith
    Legendary
    *
    Offline Offline

    Activity: 1470
    Merit: 1001


    Use Coinbase Account almosanywhere with Shift card


    View Profile WWW
    November 05, 2013, 06:00:05 AM
     #107
    Quote from: nite423 on November 05, 2013, 04:26:31 AM
    Finally got my five fury's rolling this morning, I'm running CGMiner 3.7.0 on Windows 7.

    After 12 hours running I have still yet to get a single hardware error, but the overall hash speeds have been a little disappointing.  I do have one miner that is pushing 2.4 Gh/s but then they go south from there.  Two are running around 2.2 Gh/s, one is clinging at 2.0 Gh/s and the slowest is chugging around 1.8 Gh/s. 

    I'm guessing that I (along with others) are just needing to wait for some tweaks (drivers/firmware/CG-BFG miner updates) to come along to help squeeze more out of these little monsters. 

    Used Zadig (win7)  drivers shows in devices as Bitfury BF1 USB Miner (COM12) down loaded CGMiner 3.7.0 Windows. But not finding Device.

     [2013-11-04 21:58:50] USB init, open device failed, err -12, you need to instal
    l a WinUSB driver for - BF1 device 6:1-i1
     [2013-11-04 21:58:50] bitfury detect (6:1) failed to initialise (incorrect devi
    ce?)
     [2013-11-04 21:58:57] USB init, open device failed, err -12, you need to instal
    l a WinUSB driver for - BF1 device 6:1-i1
     [2013-11-04 21:58:57] bitfury detect (6:1) failed to initialise (incorrect devi
    ce?)
    Merge mine BLC+PHO+ELT+XDQ+BBTC+UMO+LIT pool is open http://la1.blakecoin.com tips: 1MogRiTHpQZ7bkpq49cSVWADrTt7Jrghp

  • FrontLineFodder
    Newbie
    *
    Offline Offline

    Activity: 28
    Merit: 0


    View Profile
    November 05, 2013, 06:22:56 AM
     #108
    G'Day,
    Received my order from Julz yesterday, up and running with bfgminer on ubuntu, all good (error rate is way out there, however hashrate and score show correctly in the pool).

    I'm using the 10 port aluminium Orico usb hubs (A3H10 http://en.orico.com.cn/info.aspx?pid=336), the profile of the heatsink on the fury's mean that I am unable to use all 10 ports on the hub.
    The heatsink pictured by klintay (https://bt.irlbtc.com/view/299295.msg3421456#msg3421456) appears to be lower profile and has fins in a better orientation for my airflow setup.
    Assuming i can find better heatsinks, is there any recommendations on how to remove the current one ? It appears to be glued on.

  • nite423
    Newbie
    *
    Offline Offline

    Activity: 47
    Merit: 0



    View Profile
    November 05, 2013, 06:24:43 AM
     #109
    Quote from: mogrith on November 05, 2013, 06:00:05 AM

    Used Zadig (win7)  drivers shows in devices as Bitfury BF1 USB Miner (COM12) down loaded CGMiner 3.7.0 Windows. But not finding Device.

     [2013-11-04 21:58:50] USB init, open device failed, err -12, you need to instal
    l a WinUSB driver for - BF1 device 6:1-i1
     [2013-11-04 21:58:50] bitfury detect (6:1) failed to initialise (incorrect devi
    ce?)
     [2013-11-04 21:58:57] USB init, open device failed, err -12, you need to instal
    l a WinUSB driver for - BF1 device 6:1-i1
     [2013-11-04 21:58:57] bitfury detect (6:1) failed to initialise (incorrect devi
    ce?)



    I used Zadig v2.0.1.160.  After I plugged in the first BF I used Zadig to change the driver and then started CGMiner 3.7.0.  After that, all I had to do was plug in each BF one at a time and let it do its thing to each one. 

    I restarted my PC running all of this and I've gained a little bit of speed on some miners.  Like I said, maybe in a few days some updates will help squeeze out a bit more speed...

    https://dl.dropboxusercontent.com/u/102291459/CGminer.jpg

  • Beastlymac (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 630
    Merit: 501


    Miner Setup And Reviews. WASP Rep.


    View Profile
    November 05, 2013, 09:11:55 AM
    Last edit: November 05, 2013, 09:48:07 AM by Beastlymac
     #110
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.

    Edit. It is possible to overclock the units and push them to potentially 2.7 by replacing the 22k resistor with a 10k one.
    Message me if you have any problems

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    November 05, 2013, 09:31:01 AM
     #111
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.

  • Epinnoia
    Full Member
    ***
    Offline Offline

    Activity: 209
    Merit: 100


    View Profile
    November 05, 2013, 09:38:16 AM
     #112
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.

    I paid for two of them -- 2.6Gh/sec x 2.  +-10%.  The one that arrived is barely able to sustain 1.4Gh/sec!!   The one I have is clearly defective and not performing anywhere near what was advertised/promised.  I was told in PM that they screwed up something in the firmware.  I don't want coupons.  I want 2.6Gh/sec x 2 +-10% or my money returned.
    My first miner -> ATI 4550 (7.2 Mh/sec): 
    https://www.facebook.com/groups/cryptospeculators/

  • Zeek_W
    Sr. Member
    ****
    Offline Offline

    Activity: 336
    Merit: 250



    View Profile
    November 05, 2013, 09:39:47 AM
     #113
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.
    Yeah I'm only running 2.28 aswell. And after correctly installing the given drivers and editing the .bat file correctly (as in the supplied guide didn't work)
    ▓▓▓ BITMIXER.IO ▓▓▓▓▓▓ High Volume Bitcoin MIXER ▓▓▓

  • Beastlymac (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 630
    Merit: 501


    Miner Setup And Reviews. WASP Rep.


    View Profile
    November 05, 2013, 09:49:15 AM
     #114
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.
    Currently we are looking at providing coupons to people for our next batch of usbs. I have sent the firmware to Luke-jr and Ckolivas to look over and it is possible that the firmware can be optimised or issues fixed. If it is I will release it with information on how to flash it to devices.
    Message me if you have any problems

  • Epinnoia
    Full Member
    ***
    Offline Offline

    Activity: 209
    Merit: 100


    View Profile
    November 05, 2013, 09:57:30 AM
     #115
    Quote from: Beastlymac on November 05, 2013, 09:49:15 AM
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.
    Currently we are looking at providing coupons to people for our next batch of usbs. I have sent the firmware to Luke-jr and Ckolivas to look over and it is possible that the firmware can be optimised or issues fixed. If it is I will release it with information on how to flash it to devices.

    I'll be willing to talk coupons and a device that does 2.2 or 2.3 Gh/sec.  But under no circumstances am I going to be content to receive just coupons for a device that does only 1.4 Gh/sec.  I will contact Paypal before that, you can be assured.
    My first miner -> ATI 4550 (7.2 Mh/sec): 
    https://www.facebook.com/groups/cryptospeculators/

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    November 05, 2013, 10:17:46 AM
     #116
    Tried cgminer 3.7.0, got lower hash rate than bfgminer32-3.2.0

    At least now the BF1 is detected, however the sign that something is not right is that instead of alternating between red and orange, the LED flashes red/off.

  • Beastlymac (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 630
    Merit: 501


    Miner Setup And Reviews. WASP Rep.


    View Profile
    November 05, 2013, 10:19:03 AM
     #117
    Quote from: kabopar on November 05, 2013, 10:17:46 AM
    Tried cgminer 3.7.0, got lower hash rate than bfgminer32-3.2.0

    At least now the BF1 is detected, however the sign that something is not right is that instead of alternating between red and orange, the LED flashes red/off.
    Stop cgminer Hit the rst button then restart cgminer.
    Message me if you have any problems

  • visdude
    Legendary
    *
    Offline Offline

    Activity: 1081
    Merit: 1001


    View Profile
    November 05, 2013, 10:20:03 AM
     #118
    Quote from: Beastlymac on November 05, 2013, 09:49:15 AM
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.
    Currently we are looking at providing coupons to people for our next batch of usbs. I have sent the firmware to Luke-jr and Ckolivas to look over and it is possible that the firmware can be optimised or issues fixed. If it is I will release it with information on how to flash it to devices.

    But wait a minute.  I haven't even gotten my 0.05 btc/unit compensation yet.  Can I get those first?  How?

  • Beastlymac (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 630
    Merit: 501


    Miner Setup And Reviews. WASP Rep.


    View Profile
    November 05, 2013, 10:21:42 AM
     #119
    Quote from: visdude on November 05, 2013, 10:20:03 AM
    Quote from: Beastlymac on November 05, 2013, 09:49:15 AM
    Quote from: kabopar on November 05, 2013, 09:31:01 AM
    Quote from: Beastlymac on November 05, 2013, 09:11:55 AM
    I have talked with our EE he has said that the hashrate of 2.2ghs is because of the bitfury chip. He says that this is the average that people will be getting. If you are lucky you can get units that perform higher or if you aren't lucky you could potentially get some worse units it all depends on the bitfury chip. It seems when we build prototypes that we where lucky with the chips that we received.
    For fairness, the burden of this 'bad luck' should be carried mainly by the seller, not by the consumers. The specified claimed performance was "Spec: Rated speed 2.6Gh/s. +/- 10%" (https://bt.irlbtc.com/view/299295.0. You probably need to consider some sort of compensation, for example in coupons on future sales, rather than 'passing the buck' and blaming luck.
    Currently we are looking at providing coupons to people for our next batch of usbs. I have sent the firmware to Luke-jr and Ckolivas to look over and it is possible that the firmware can be optimised or issues fixed. If it is I will release it with information on how to flash it to devices.

    But wait a minute.  I haven't even gotten my 0.05 btc/unit compensation yet.  Can I get those first?  How?

    Who is your groupbuy leader?
    Message me if you have any problems

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    November 05, 2013, 10:29:19 AM
     #120
    Quote from: Beastlymac on November 05, 2013, 10:19:03 AM
    Quote from: kabopar on November 05, 2013, 10:17:46 AM
    Tried cgminer 3.7.0, got lower hash rate than bfgminer32-3.2.0

    At least now the BF1 is detected, however the sign that something is not right is that instead of alternating between red and orange, the LED flashes red/off.
    Stop cgminer Hit the rst button then restart cgminer.
    Tried this, the LED lights up in orange briefly, but after being re-detected by cgminer it flashes red/off, and the hash rate remains as before...
    Pages: « 1 2 3 4 5 [6] 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 »
      Print  
Page 5
Viewing Page: 6

IRLBTC™ © 2025 IRLBTC.com