<<  >> (p.79)
    Author Topic: ANTMINER S3+ Discussion and Support Thread  (Read 710629 times)

    • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 06:43:16 AM
     #1561
    Received my First order of 2xS3 Antminers today.
    They are seems very professional.
    Their weight was more than S1 Antminers.
    They both setup very smoothly with an Enermax 1000 PSU.





    But the problem is that one card of one of S3's is not working at all!




    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?
    Sepehr, A Cryptocurrency Evangelist

  • Lowell904
    Member
    **
    Offline Offline

    Activity: 119
    Merit: 10


    View Profile
    July 20, 2014, 06:52:12 AM
     #1562
    Quote from: sepehr on July 20, 2014, 06:43:16 AM
    Received my First order of 2xS3 Antminers today.
    They are seems very professional.
    Their weight was more than S1 Antminers.
    They both setup very smoothly with an Enermax 1000 PSU.





    But the problem is that one card of one of S3's is not working at all!




    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 06:55:50 AM
     #1563
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
    Sepehr, A Cryptocurrency Evangelist

  • raspberrypirobot
    Newbie
    *
    Offline Offline

    Activity: 14
    Merit: 0


    View Profile
    July 20, 2014, 07:49:21 AM
     #1564
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 07:59:02 AM
     #1565
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Sepehr, A Cryptocurrency Evangelist

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    July 20, 2014, 07:59:19 AM
     #1566
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
    What happens if you connect the cables from your PSU that worked with the 'good' unit just to the 'bad' unit?  (checking the possibility that there is some issue in your PSU or its cables)

    Cheers

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    July 20, 2014, 08:01:15 AM
     #1567
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 08:02:26 AM
     #1568
    Quote from: kabopar on July 20, 2014, 07:59:19 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
    What happens if you connect the cables from your PSU that worked with the 'good' unit just to the 'bad' unit?  (checking the possibility that there is some issue in your PSU or its cables)

    Cheers

    Did all these and no change!

    Thanks s lot for your attention
    Sepehr, A Cryptocurrency Evangelist

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 08:03:34 AM
     #1569
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    Sepehr, A Cryptocurrency Evangelist

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    July 20, 2014, 08:27:37 AM
     #1570
    Quote from: sepehr on July 20, 2014, 08:03:34 AM
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    If it's not some obvious workmanship problem related to the main-board connector (dry solder joint on the socket to the 'bad' board), then it's probably an RMA issue with BITMAIN.  If you want to prove this 'beyond doubt' you could swap controller boards between your 2 Antminers. Ideally they would provide the replacement main-board so that you can continue mining with the 'half' miner while the replacement is shipped to your rather than loosing the whole turn-around time.

    Cheers

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 08:46:01 AM
     #1571
    Quote from: kabopar on July 20, 2014, 08:27:37 AM
    Quote from: sepehr on July 20, 2014, 08:03:34 AM
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    If it's not some obvious workmanship problem related to the main-board connector (dry solder joint on the socket to the 'bad' board), then it's probably an RMA issue with BITMAIN.  If you want to prove this 'beyond doubt' you could swap controller boards between your 2 Antminers. Ideally they would provide the replacement main-board so that you can continue mining with the 'half' miner while the replacement is shipped to your rather than loosing the whole turn-around time.

    Cheers

    As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
    I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity. Sad

    Thanks a lot guys!
    Sepehr, A Cryptocurrency Evangelist

  • BITMAIN (OP)
    Hero Member
    *****
    Offline Offline

    Activity: 741
    Merit: 514


    https://www.bitmain.com


    View Profile WWW
    July 20, 2014, 08:58:07 AM
     #1572
    Quote from: sepehr on July 20, 2014, 08:46:01 AM
    Quote from: kabopar on July 20, 2014, 08:27:37 AM
    Quote from: sepehr on July 20, 2014, 08:03:34 AM
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    If it's not some obvious workmanship problem related to the main-board connector (dry solder joint on the socket to the 'bad' board), then it's probably an RMA issue with BITMAIN.  If you want to prove this 'beyond doubt' you could swap controller boards between your 2 Antminers. Ideally they would provide the replacement main-board so that you can continue mining with the 'half' miner while the replacement is shipped to your rather than loosing the whole turn-around time.

    Cheers

    As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
    I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity. Sad

    Thanks a lot guys!

    Hi,

    RMA request is accepted, PMed you just now.
    Cloud Mining? Just Go to Hashnest.com          Best Liquidity   Lowest Price   100% Real Mining Back Up

  • smilingloki
    Member
    **
    Offline Offline

    Activity: 73
    Merit: 10


    View Profile
    July 20, 2014, 09:18:34 AM
     #1573
    BITMAIN Order Shipped B2's
    •   Order ID: 00XXXXXXXXXXXXXXXXXXXXXXXXXX
    •   Date: 2014-07-03 10:25:13

    Fantastic! as promised on or just after the 20th Smiley

    very happy!

  • sepehr
    Sr. Member
    ****
    Offline Offline

    Activity: 399
    Merit: 250


    Cryptocurrency Evangelist


    View Profile
    July 20, 2014, 09:25:19 AM
     #1574
    Quote from: BITMAIN on July 20, 2014, 08:58:07 AM
    Quote from: sepehr on July 20, 2014, 08:46:01 AM
    Quote from: kabopar on July 20, 2014, 08:27:37 AM
    Quote from: sepehr on July 20, 2014, 08:03:34 AM
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    If it's not some obvious workmanship problem related to the main-board connector (dry solder joint on the socket to the 'bad' board), then it's probably an RMA issue with BITMAIN.  If you want to prove this 'beyond doubt' you could swap controller boards between your 2 Antminers. Ideally they would provide the replacement main-board so that you can continue mining with the 'half' miner while the replacement is shipped to your rather than loosing the whole turn-around time.

    Cheers

    As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
    I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity. Sad

    Thanks a lot guys!

    Hi,

    RMA request is accepted, PMed you just now.


    Thank you! you can send it with my other orders.
    Sepehr, A Cryptocurrency Evangelist

  • Trammel
    Newbie
    *
    Offline Offline

    Activity: 47
    Merit: 0


    View Profile
    July 20, 2014, 09:55:54 AM
     #1575
    My batch 2 order is on its way.

    Info from Bitmain Website

    Order Placed
    Date:  2014-07-04 12:56:46

    Payment Confirmed:
    Date   2014-07-04 14:07:48

    Shipped:
    Date   2014-07-20 08:18:59

    Hopefully will receive on Tuesday, and hope all arrives safely.

  • oskuro
    Sr. Member
    ****
    Offline Offline

    Activity: 294
    Merit: 251


    View Profile
    July 20, 2014, 09:56:25 AM
     #1576
    Batch 2

    Pay:1.48 BTC
    Confirm:1.48 BTC   Paid
    Shipped
    Valid   2014-07-02 10:03:41.0

    Yesssss!!!!!!  Smiley

  • oskuro
    Sr. Member
    ****
    Offline Offline

    Activity: 294
    Merit: 251


    View Profile
    July 20, 2014, 10:23:59 AM
     #1577
    Quote from: jelin1984 on July 20, 2014, 10:22:08 AM
    Why every newbie buy from bit main
    You will never roi
    Because diff go so up
    Because of bit main hardware
    So the only which is earn is bitmain no one else
    You never roi your money you spent


    I take this as a hobbie and it will roi.  Anyway what are you doing here if you hate bitmain? 

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    July 20, 2014, 10:34:36 AM
     #1578
    Quote from: sepehr on July 20, 2014, 09:25:19 AM
    Quote from: BITMAIN on July 20, 2014, 08:58:07 AM
    Quote from: sepehr on July 20, 2014, 08:46:01 AM
    Quote from: kabopar on July 20, 2014, 08:27:37 AM
    Quote from: sepehr on July 20, 2014, 08:03:34 AM
    Quote from: kabopar on July 20, 2014, 08:01:15 AM
    Quote from: sepehr on July 20, 2014, 07:59:02 AM
    Quote from: raspberrypirobot on July 20, 2014, 07:49:21 AM
    Quote from: sepehr on July 20, 2014, 06:55:50 AM
    Quote from: Lowell904 on July 20, 2014, 06:52:12 AM
    Quote from: sepehr on July 20, 2014, 06:43:16 AM

    But the problem is that one card of one of S3's is not working at all!

    I have checked everything power, cabling, anything I can imagine but it persist and not working at all!

    Any ideas what should I do?

    Did you try moving the cables to the other ports?

    Otherwise,  I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.

    Yes, tried it and open it up as well but found no problem yet!
    Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!

    It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.

    there is no shipment problem seems on the device.
    But I found a clue.
    I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.

    Now the other board is mining and it's temperature increased.

    So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
    Looks like its time to swap cables between your 'good' unit and the 'bad' one.  Maybe its just a single faulty ribbon cable between the controller and the hashing boards.

    Cheers

    ribbon cables are ok. tried this before.
    If it's not some obvious workmanship problem related to the main-board connector (dry solder joint on the socket to the 'bad' board), then it's probably an RMA issue with BITMAIN.  If you want to prove this 'beyond doubt' you could swap controller boards between your 2 Antminers. Ideally they would provide the replacement main-board so that you can continue mining with the 'half' miner while the replacement is shipped to your rather than loosing the whole turn-around time.

    Cheers

    As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
    I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity. Sad

    Thanks a lot guys!

    Hi,

    RMA request is accepted, PMed you just now.


    Thank you! you can send it with my other orders.
    Looks like the script for a 'happy end' Smiley
    Congrats!

  • kabopar
    Hero Member
    *****
    Offline Offline

    Activity: 616
    Merit: 500


    View Profile
    July 20, 2014, 10:36:41 AM
     #1579
    Quote from: oskuro on July 20, 2014, 09:56:25 AM
    Batch 2

    Pay:1.48 BTC
    Confirm:1.48 BTC   Paid
    Shipped
    Valid   2014-07-02 10:03:41.0

    Yesssss!!!!!!  Smiley
    Congrats!  Wish you a quick delivery

    I also got the delivery info and am following the tracking, unfortunately the weekend seems to put a bit of a pause, so current delivery of my B1 order is now expected on Wednesday.

    Cheers

  • JennaK
    Newbie
    *
    Offline Offline

    Activity: 42
    Merit: 0


    View Profile
    July 20, 2014, 10:37:54 AM
     #1580
    I get Free electricity at my dorm! I wish I could buy one so I could mine. Would be fun!
    Enjoy your ant miners guys.
    Pages: « 1 ... 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 [79] 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 ... 515 »
      Print  
Page 78
Viewing Page: 79

IRLBTC™ © 2025 IRLBTC.com