To setup remote re-configuration of rigs remote viewing using SSH and screen:


PREP RIGS:

On each rig you wish to ssh into ensure:



in 1bash

have your phone or a pencil and paper with you as you will also need the ip address of each rig:

to find the ip:

scroll to the top of the mining process where is shows:


find this ip and record it with a picture or write it down save it to a text file ect.

When you have finished this with each rig; go to the computer you are going to use to ssh from:


SETUP CLIENT:

If it is a windows computer I recommend using putty: http://www.putty.org/ for this as it will let you use as many instances into as many rigs as you want.

for each rig open a new putty instance then:

enter:


replacing ipaddress with the miners ip from eariler; if it was 192.168.1.124, then you would enter:


and click open





confirm your intent to access the system if asked, then enter password:

miner1

when prompted

Then move on to the Reconfigure section below:


If you are on a linux computer:

open a terminal and enter:


when it is done:

for each rig open a new terminal instance or tab then:

enter:


replacing ipaddress with the miners ip from eariler; if it was 192.168.1.124, then you would enter:


confirm your intent to access the system if asked, then enter password:

miner1

when prompted

Then move on to the Reconfigure section below:



RECONFIGURE:


after SSHing into a rig:

open 1bash with nano:


make changes edits; then press ctrl + shift + X to quit selecting Y to save changes

Then:

we need to kill the current mining process by entering:


now we have stopped the GPU mining process



SCREEN:

after killing the current mining process:

enter this to prevent a possible error:


Then attach to the current mining process screen (v0018 will auto restart the mining process):



if you are updating for _Parallax_ Mode enter:


then


and you have remote viewing of the mining process in this screen.

you can close the ssh session (window terminal) whenever desired

then later reSSH in and enter:


to return to the mining process whenever desired.


If you are at this point and have a farm command center PC:  Congratulations!  


Right now the simplest way to setup Internet access to your rigs is this:

Setup a single computer with SSH sessions into each rig (I recommend saving each session config or making a file with the settings to launch each.)  

On this computer install Teamviewer or a similar application.  

Connect via your mobile tablet work computer ect to the control computer with Teamviewer or similar application, then on that rig Monitor reconfigure each rig via its SSH session.

This should be reasonably simple (given the complexity of what you are doing) to setup.


See the _Parallax_ Mode guide for autoupdating oneBash Link


Additional useful cmds for Screen from UberDaemon:

To detach from a screen (i.e. you want to close the SSH connection while mining continues afterwards) it's


To reattach to a screen (resume connection) it's

 # once you've typed 3-4 characters hit the tab key and it will fill out the rest and save you some typing

If you can't remember what you named the session use:


If you're new to screen you may not know you can open a 2nd shell and switch back and forth (i.e. your miner is running on one shell and you open a 2nd to run nvidia-smi):

once in screen you create a 2nd shell (or 3rd, 4th, etc) with

To switch back and forth use:

I should not edit mph_conf.json ?

but another question, does it calculate/benchamrk my hash rate ?
I have 6 1070 in this rig and the profit shows :


So at best I get 4.4$/day with my 6 cards ?

How do I chose which algos/coins to mine on MPH?

@papampi
Thanks for your reply.

Sorry for my to long initial post  

I've launched (gueke) sudo apt-get install libutempter0 + reboot.

No more warns now but still no mining process ... computer still in reboot's loop after some minutes (no process to run).

If you have ideas to solve this problem, there are welcome.


@VoskCoin
Thanks for your reply.

I'm usign Putty on my win10 pc to control my rig and I've also tried the local mode with the first gpu near the processor but no mining process at all even after my sudo apt-get install libutempter0 + reboot.

In order to be sure, when you say that with suprnova I need to use username/workername in 1bash, maybe it's a part of my problem.

I have an account with suprnova (zen) and also have a worker so - for example - if my suprnova username is gaol and my worker name is the same, how must I write correctly this in my 1bash's zenworker ? must I use : gaol.gaol ? or must I use a slash or something else ?

Same question with my worker password, where to put it in 1bash setup ?

If you have ideas to solve this problem, there are welcome.

_S_C_

There was one instance a week or so ago where switching stopped; a reboot fixed that, and it's not happened again since.  I don't know why it did that...temporary blockage of MiningPoolHub's API, perhaps?

It has to go like this:

Worker is what you add on suprnova portal

Code:

ZEN_WORKER="gaol"


Address is your username for logging into suprnova portal

Code:

ZEN_ADDRESS="gaol"

@damNmad

Thanx for your reply.


Now all working fine ...

After some minutes I have >750 sol/s per GPU. Is it a good number for a gtx1080ti ?

I probably need to twicking powerlimit cc cm ...

By the way, powerlimit is a watt number but I just don't know if cc and/or cm are for Mhz or % ?

What's your favorite overclocking or dowclocking numbers (powerlimit cc cm) for a MSI Geforce gtx1080ti Gaming OC ?

In advance, thanks for your help.

_S_C_

just type following :
                    => + return     it's to see the actual running jobs

if you are mining, normaly, you should see 3 jobs :
1) the miner
2) temp (assuming temp supervision is on yes in your bash file)
3) watchdog (assuming wdog supervision is on yes in your bash file)

to see each job type the following :
               => + return    it's to see your mining jobs

                    => to exit the miner windows

same for the other jobs
                 => + return
 

                => + return


then type :
                          => + return      it's to close your ssh session but the jobs still running

if you want to change your bash file, just type :
               => + return      nano it's a text editor - you can change what you want then ctrl + o to write out then return
                                                      then ctrl + x to close nano

if you change your bash file, you need to kill the miner
so for that, just type :
              => + return
after some seconds, your mining process restart by itself
to see if all working ok, just type :
                 

Regards.