I can not install KTccminer on NVOCv019.

I looked at your post on their incident ticket page and I find that 4 days ago you were able to compile it correctly on your machine.
Unfortunately, I have not managed to do the same with my Biostar TB250-BTC PRO (Socket 1151) and my 2 x ASUS GTX1070 DUAL.

I use the script (s) of Scott ALlfter (alias Salfter) and I went on his page here: https://gitlab.com/salfter/mph_switch/tree/master. This page explains how to add the Cryptonight and Sia miners but I was unable to compile by following the command lines given by Salfter.

./autoreconf.sh does not exist in the KTccminer directory
and
./configure --with-cuda- usr local cuda-8.0 also returns errors after executing the file: autogen.sh

here is what the configuration command gives me before the command make:

user @ hostname $ KTccminer-cryptonight $ ./configure --with-cuda usr local cuda
configure: WARNING: you should use --build, --host, --target
configure: WARNING: invalid host type: usr local cuda
checking build system type ... usr local cuda
configure: error: invalid value of canonical build

It seems to me to have found by re-reading the bash-history that it tries to mine with the CPUminer which mine at the same time as ETH and the others algo.
is it possible to mining with CPUs and GPUs with two different software simultaneously without it posing bp?
That is, I use Scott's mining profit switching script and I have activated the plusCPU function of fullZERO in the 1bash

1 How to install KTccminer correctly?
2 Is it possible to mine monero with the CPUs in addition to the GPUs ?

@Scott Alfter

The use of your script delighted me, but I hesitated for a long time because of the lack of documentation. I did not know too much or I was going. and I still do not really know where all the files you are using.

Maybe you have some documentation about these scripts?

NB: I used google translation to write this message

I finally got around to upgrading to v19 from v17.  I'd had some trouble with v18 and went back to v17, but v19's being much better behaved.  I put my config in (configured to use my MiningPoolHub switcher and Maxximus007's fan-control code) and let her rip.

There is one issue I ran across: no Cryptonight miner.  I noticed it when my mining rig's fans all slowed down.  To get things running again in a hurry, I copied the mining software from my v17 setup.  It's in this tarball:

https://alfter.us/wp/wp-content/uploads/2017/09/KTccminer-cryptonight.tar.xz

Unpack to ~m1. It'll unpack to a Git repo into which you can pull updates (I last updated it just a few days ago) that has already been configured and built.  I might've built it for Pascal (GeForce 10-series) GPUs only; I don't recall for sure if I did, so if you're using older GPUs and it doesn't work for you, you might need to rebuild it.

There was also an upstream change in this miner that requires a change in 3main.  The "-a cryptonight" option is no longer accepted, so load 3main into the editor of your choice, search for "KTccminer-cryptonight" (it's near the beginning of the heredoc that gets written to mph_conf.json), and delete "-a cryptonight" from that line.

Beyond that, the only other changes I made were to set the hostname equal to the worker name (changes inetc/hostname andetc/hosts), change the timezone from Eastern to Pacific, and to revise the speed and power figures in the mph_conf.json heredoc with my current configuration (up from 3 GPUs to 4).  As I write this, I'm imaging my v19 setup so I can copy it over to the (physically smaller) stick with v17.

If you just want KTccminer-cryptonight salfter has compiled one :


I could compile KTccminer on nv0019, but not on my other ubuntu
gave me some errors
just download the source
and run the commands with no args
it should be ok

Why you wana set it to 25 or lower ?
Even a standby GPU temp is higher than that.
Dont kill your fans just to take temp down.

I've issue with connecting to stratum pool using EWBF;

try this:



This should work; let me know if it doesn't.

ok progress has been made but now I am getting a stratum authorization error. below is basically what I have. do I not need to put the worker password somewhere? also I do appreciate the help. thanks

ZEN_WORKER="tempworker1"
ZEN_ADDRESS="yourSuprNovaLoginName"
ZEN_POOL="zen.suprnova.cc"
ZEN_PORT="3618"


well I feel real stupid. I am up and running. thank you for the help. I miss typed name I used the log in info not the user name. it was a me issue lol

Hello papampi; hope you are well

I believe we can compile it well but when we try to use it fails to mine with some weird errors!! or it has been fixed?