<<  >> (p.31)
    Author Topic: [ANN] TeamRedMiner - Old Thread  (Read 85807 times)

    • peteris-apse
    Jr. Member
    *
    Offline Offline

    Activity: 98
    Merit: 1


    View Profile
    July 04, 2019, 11:28:38 AM
     #601
    Is this algo ram dependent? now i am having like 2.6-2.7 on vega 56 with 1350 on core and 300 mem, it is drawing like 200 per card from wall (my guess, i dont have data on this from remote computer).

  • professorkuusamo
    Newbie
    *
    Offline Offline

    Activity: 14
    Merit: 0


    View Profile
    July 04, 2019, 11:43:18 AM
     #602
    vega 64 3,5 from wall 280w
    vega 56 3,3 from wall 270w
    settings like cryptonight r

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 04, 2019, 11:47:20 AM
     #603
    Quote from: peteris-apse on July 04, 2019, 11:28:38 AM
    Is this algo ram dependent? now i am having like 2.6-2.7 on vega 56 with 1350 on core and 300 mem, it is drawing like 200 per card from wall (my guess, i dont have data on this from remote computer).

    It is certainly ram dependent in that it needs ~4.5GB just to run. Given the mem access patterns, you can clock down memory a ton on Vegas (but not on Polaris cards), just like you've done. I actually think your core clk could be unnecessarily high, but the only way to know for sure is to continue tweaking. Since you're running on 300 memclk, I'm guessing you're already down in lower mem P-states? That is the preferred way since it will drop the soc clk, allowing for a much lower voltage for core + mem (as configured in e.g. OverdriveNTool). I've ran my tests down to 500 MHz memclk, but that's on Vega 64s.

    You might already have read it, but I did write a little about the tuning process in the MTP_MINING.txt in the release package.

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 04, 2019, 11:50:35 AM
     #604
    Quote from: professorkuusamo on July 04, 2019, 11:43:18 AM
    vega 64 3,5 from wall 280w
    vega 56 3,3 from wall 270w
    settings like cryptonight r

    Yes, the power draw is nuts even on standard CN clocks. Naturally it depends on your power cost, but in many cases you still earn a higher net profit using these crazy settings than clocking down and getting maybe 2.8-2.9 MH/s on a Vega 64 at a more reasonable (but still high) power draw. This algo will always pull a lot of power, it's by design unfortunately.

    Compared to CN, you can seriously clock down mem though to save on power, it gives you a too small of a hashrate boost to justify the power draw. As stated above, details included in the release package in MTP_MINING.txt.

  • kokodesu
    Newbie
    *
    Offline Offline

    Activity: 42
    Merit: 0


    View Profile
    July 04, 2019, 12:24:53 PM
     #605
    Quote from: kerney666 on July 04, 2019, 10:47:51 AM
    Quote from: kokodesu on July 04, 2019, 01:43:02 AM
    Thank you for adding MTP Argo.
    It's a shame that you can not do it with a 4GB GPU, but it may be difficult.

    win10
    RX570 8G 1100/1800 about 1Mhz
    RX580 8G 1340/2000 about 1.6Mhz

    It was described in the wrong thread. I am sorry.

    Thank you for testing! However, I must say your results are low compared to expected values, you should be able to hit ~1.6 MH/s (570) and ~1.8 MH/s (580) without too much tuning effort. I'll do a proper benchmark post soon, listing hashrates and settings for range of gpus.


    Yes, I think my hash rate is low.
    However, with regard to the problems of temperature and power, and with regard to the RX 570,
    there is a present condition that is suppressed because it is an individual that can not make much memory OC.

    In addition, there is also a thing that usually using HiveOS, there was also the aspect that it tested easily.

    HiveOS
    RX570 1100/875 1800/900 about 1.1Mhz
    RX580 1100/875 2100/900 about 1.7Mhz

    It is suppressed by the problem of temperature and power.

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 04, 2019, 01:07:26 PM
     #606
    Quote from: kokodesu on July 04, 2019, 12:24:53 PM
    Quote from: kerney666 on July 04, 2019, 10:47:51 AM
    Quote from: kokodesu on July 04, 2019, 01:43:02 AM
    Thank you for adding MTP Argo.
    It's a shame that you can not do it with a 4GB GPU, but it may be difficult.

    win10
    RX570 8G 1100/1800 about 1Mhz
    RX580 8G 1340/2000 about 1.6Mhz

    It was described in the wrong thread. I am sorry.

    Thank you for testing! However, I must say your results are low compared to expected values, you should be able to hit ~1.6 MH/s (570) and ~1.8 MH/s (580) without too much tuning effort. I'll do a proper benchmark post soon, listing hashrates and settings for range of gpus.


    Yes, I think my hash rate is low.
    However, with regard to the problems of temperature and power, and with regard to the RX 570,
    there is a present condition that is suppressed because it is an individual that can not make much memory OC.

    In addition, there is also a thing that usually using HiveOS, there was also the aspect that it tested easily.

    HiveOS
    RX570 1100/875 1800/900 about 1.1Mhz
    RX580 1100/875 2000/900 about 1.7Mhz

    It is suppressed by the problem of temperature and power.

    Yes, you can definitely hit thermal throttling scenarios if the fans aren't cranked up high enough, or if you're in a warm location (like most of us this time of year).

  • hbouma
    Newbie
    *
    Offline Offline

    Activity: 22
    Merit: 0


    View Profile
    July 05, 2019, 03:39:19 AM
     #607
    Quote from: todxx on July 03, 2019, 06:44:57 PM
    Team Red Miner v0.5.3 released

    Now supporting the MTP algorithm for Zcoin Smiley


    As mentioned at mintpond, the miner always exits when creating the scratchpad while being ran from awesome miner. I'll get the spinning cursor for a moment and then it will exit. If I try the diagnostic mode, it runs. If I run it using the included batch file, it works there too. So I'm not sure what is up. This is on Windows 10 with A6-3500 APU and RX 470 and RX 580 cards with 18.6.1. drivers. I've been mining with sgminer-fancyl and djm34's miner for weeks before this without problems I would think the settings/hardware should be fine to at least get the miner to start. lol.

    Thanks for taking the time to add MTP support!

    Hal

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 05, 2019, 05:23:42 AM
     #608
    Quote from: hbouma on July 05, 2019, 03:39:19 AM
    Quote from: todxx on July 03, 2019, 06:44:57 PM
    Team Red Miner v0.5.3 released

    Now supporting the MTP algorithm for Zcoin Smiley


    As mentioned at mintpond, the miner always exits when creating the scratchpad while being ran from awesome miner. I'll get the spinning cursor for a moment and then it will exit. If I try the diagnostic mode, it runs. If I run it using the included batch file, it works there too. So I'm not sure what is up. This is on Windows 10 with A6-3500 APU and RX 470 and RX 580 cards with 18.6.1. drivers. I've been mining with sgminer-fancyl and djm34's miner for weeks before this without problems I would think the settings/hardware should be fine to at least get the miner to start. lol.

    Thanks for taking the time to add MTP support!

    Hal

    Well that’s odd. Of course the hardware works fine if you can run it both in diagnostic mode and outside of AM Smiley. Not sure this is our issue (but it could very well be). Have you talked to the Awesome Miner guys? I’m traveling today but will try to test as soon as I can. I don’t have a good AM setup right now though but I’ll try to sort it out.

  • joseph32
    Member
    **
    Offline Offline

    Activity: 418
    Merit: 21


    View Profile
    July 05, 2019, 05:25:11 AM
     #609
    Quote from: hbouma on July 05, 2019, 03:39:19 AM
    Quote from: todxx on July 03, 2019, 06:44:57 PM
    Team Red Miner v0.5.3 released

    Now supporting the MTP algorithm for Zcoin Smiley


    As mentioned at mintpond, the miner always exits when creating the scratchpad while being ran from awesome miner. I'll get the spinning cursor for a moment and then it will exit. If I try the diagnostic mode, it runs. If I run it using the included batch file, it works there too. So I'm not sure what is up. This is on Windows 10 with A6-3500 APU and RX 470 and RX 580 cards with 18.6.1. drivers. I've been mining with sgminer-fancyl and djm34's miner for weeks before this without problems I would think the settings/hardware should be fine to at least get the miner to start. lol.

    Thanks for taking the time to add MTP support!

    Hal

    Already made a post in Patrik's thread about that issue: https://bt.irlbtc.com/view/676942.msg51710602#msg51710602

    Edit @ Kerney: You can use just the standard setup. Its the same command line. In AM it crashs, without AM it runs. Would be great if we can sort out this bug.

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 05, 2019, 05:52:52 AM
     #610
    Quote from: joseph32 on July 05, 2019, 05:25:11 AM
    Quote from: hbouma on July 05, 2019, 03:39:19 AM
    Quote from: todxx on July 03, 2019, 06:44:57 PM
    Team Red Miner v0.5.3 released

    Now supporting the MTP algorithm for Zcoin Smiley


    As mentioned at mintpond, the miner always exits when creating the scratchpad while being ran from awesome miner. I'll get the spinning cursor for a moment and then it will exit. If I try the diagnostic mode, it runs. If I run it using the included batch file, it works there too. So I'm not sure what is up. This is on Windows 10 with A6-3500 APU and RX 470 and RX 580 cards with 18.6.1. drivers. I've been mining with sgminer-fancyl and djm34's miner for weeks before this without problems I would think the settings/hardware should be fine to at least get the miner to start. lol.

    Thanks for taking the time to add MTP support!

    Hal

    Already made a post in Patrik's thread about that issue: https://bt.irlbtc.com/view/676942.msg51710602#msg51710602

    Edit @ Kerney: You can use just the standard setup. Its the same command line. In AM it crashs, without AM it runs. Would be great if we can sort out this bug.

    +1, I dropped a note in the AM thread as well.

  • peteris-apse
    Jr. Member
    *
    Offline Offline

    Activity: 98
    Merit: 1


    View Profile
    July 05, 2019, 07:43:23 AM
     #611
    So Polaris is taking huge benefit from memory... Vegas not so much. Polaris rig is working great, but vegas...  I am still tweaking, but now i am having like weird problem with vegas where i cant get them stable. I guess i don't really understand how memory states affect core voltage. Because when i am starting to use other memory states it appears that it changes core voltage and my overclocks are not stable anymore.

  • KL0nLutiy1
    Newbie
    *
    Offline Offline

    Activity: 88
    Merit: 0


    View Profile
    July 05, 2019, 09:17:14 AM
     #612
    @kerney666, could you please add ability to mining nimiq with your miner?

  • kerney666
    Member
    **
    Offline Offline

    Activity: 658
    Merit: 86


    View Profile
    July 05, 2019, 09:46:21 PM
     #613
    Quote from: joseph32 on July 05, 2019, 05:25:11 AM
    Quote from: hbouma on July 05, 2019, 03:39:19 AM
    Quote from: todxx on July 03, 2019, 06:44:57 PM
    Team Red Miner v0.5.3 released

    Now supporting the MTP algorithm for Zcoin Smiley


    As mentioned at mintpond, the miner always exits when creating the scratchpad while being ran from awesome miner. I'll get the spinning cursor for a moment and then it will exit. If I try the diagnostic mode, it runs. If I run it using the included batch file, it works there too. So I'm not sure what is up. This is on Windows 10 with A6-3500 APU and RX 470 and RX 580 cards with 18.6.1. drivers. I've been mining with sgminer-fancyl and djm34's miner for weeks before this without problems I would think the settings/hardware should be fine to at least get the miner to start. lol.

    Thanks for taking the time to add MTP support!

    Hal

    Already made a post in Patrik's thread about that issue: https://bt.irlbtc.com/view/676942.msg51710602#msg51710602

    Edit @ Kerney: You can use just the standard setup. Its the same command line. In AM it crashs, without AM it runs. Would be great if we can sort out this bug.

    Ok, the AM issues should be fixed in v0.5.4, todxx will update with the new release shortly.

  • todxx (OP)
    Member
    **
    Offline Offline

    Activity: 176
    Merit: 76


    View Profile
    July 05, 2019, 09:54:59 PM
     #614
    Team Red Miner v0.5.4 released

    https://github.com/todxx/teamredminer/releases

    Changes in v0.5.4
    • Fixed API bug for MTP, crashing when using Awesome Miner.
    • Small MTP improvements, mostly for Polaris.

    A couple small fixes and improvements for mtp.

  • dickmo
    Newbie
    *
    Offline Offline

    Activity: 6
    Merit: 0


    View Profile
    July 05, 2019, 10:48:58 PM
     #615
    hey,dude

    Pool xzc.f2pool.com rpc method "mining.extranonce.subscribe" timed out after 69 seconds.  Reconnecting.

    could you please take a look?

  • todxx (OP)
    Member
    **
    Offline Offline

    Activity: 176
    Merit: 76


    View Profile
    July 05, 2019, 11:30:19 PM
     #616
    Quote from: dickmo on July 05, 2019, 10:48:58 PM
    hey,dude

    Pool xzc.f2pool.com rpc method "mining.extranonce.subscribe" timed out after 69 seconds.  Reconnecting.

    could you please take a look?

    Please try using the --pool_no_ensub option.

  • dickmo
    Newbie
    *
    Offline Offline

    Activity: 6
    Merit: 0


    View Profile
    July 06, 2019, 02:34:12 AM
     #617
    Quote from: todxx on July 05, 2019, 11:30:19 PM
    Quote from: dickmo on July 05, 2019, 10:48:58 PM
    hey,dude

    Pool xzc.f2pool.com rpc method "mining.extranonce.subscribe" timed out after 69 seconds.  Reconnecting.

    could you please take a look?

    Please try using the --pool_no_ensub option.

    Code:
    2019-07-06 02:29:36] GPU 3 - MTP scratchpad rebuilt in 1.66 secs.
    [2019-07-06 02:29:40] GPU 4 - MTP scratchpad rebuilt in 1.66 secs.
    [2019-07-06 02:29:41] GPU 2 - MTP scratchpad rebuilt in 1.65 secs.
    [2019-07-06 02:30:06] Stats Uptime: 0 days, 00:02:33
    [2019-07-06 02:30:06] GPU 0 [63C, fan 91%] mtp: 2.795Mh/s, avg 2.710Mh/s, pool 894.8kh/s a:1 r:0 hw:0
    [2019-07-06 02:30:06] GPU 1 [60C, fan 95%] mtp: 3.229Mh/s, avg 3.108Mh/s, pool 1.792Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:06] GPU 2 [58C, fan 95%] mtp: 2.916Mh/s, avg 2.979Mh/s, pool 1.794Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:06] GPU 3 [50C, fan 92%] mtp: 2.996Mh/s, avg 3.095Mh/s, pool 1.797Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:06] GPU 4 [57C, fan 96%] mtp: 2.946Mh/s, avg 3.001Mh/s, pool 1.799Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:06] Total                mtp: 14.88Mh/s, avg 14.89Mh/s, pool 8.077Mh/s a:9 r:0 hw:0
    [2019-07-06 02:30:15] Pool xzc.f2pool.com set difficulty to 1023.984375
    [2019-07-06 02:30:15] Pool xzc.f2pool.com received new job. (job_id: 02000000)
    [2019-07-06 02:30:36] Stats Uptime: 0 days, 00:03:03
    [2019-07-06 02:30:36] GPU 0 [64C, fan 91%] mtp: 2.815Mh/s, avg 2.727Mh/s, pool 745.6kh/s a:1 r:0 hw:0
    [2019-07-06 02:30:36] GPU 1 [60C, fan 95%] mtp: 3.229Mh/s, avg 3.132Mh/s, pool 1.493Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:36] GPU 2 [58C, fan 95%] mtp: 3.086Mh/s, avg 3.001Mh/s, pool 1.495Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:36] GPU 3 [51C, fan 92%] mtp: 3.229Mh/s, avg 3.121Mh/s, pool 1.496Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:36] GPU 4 [57C, fan 96%] mtp: 3.118Mh/s, avg 3.019Mh/s, pool 1.498Mh/s a:2 r:0 hw:0
    [2019-07-06 02:30:36] Total                mtp: 15.48Mh/s, avg 15.00Mh/s, pool 6.727Mh/s a:9 r:0 hw:0
    [2019-07-06 02:31:06] Stats Uptime: 0 days, 00:03:33
    [2019-07-06 02:31:06] GPU 0 [63C, fan 91%] mtp: 2.808Mh/s, avg 2.739Mh/s, pool 639.1kh/s a:1 r:0 hw:0
    [2019-07-06 02:31:06] GPU 1 [60C, fan 95%] mtp: 3.163Mh/s, avg 3.134Mh/s, pool 1.279Mh/s a:2 r:0 hw:0
    [2019-07-06 02:31:06] GPU 2 [58C, fan 95%] mtp: 3.085Mh/s, avg 3.012Mh/s, pool 1.281Mh/s a:2 r:0 hw:0
    [2019-07-06 02:31:06] GPU 3 [51C, fan 92%] mtp: 3.229Mh/s, avg 3.135Mh/s, pool 1.282Mh/s a:2 r:0 hw:0
    [2019-07-06 02:31:06] GPU 4 [57C, fan 96%] mtp: 3.089Mh/s, avg 3.027Mh/s, pool 1.283Mh/s a:2 r:0 hw:0
    [2019-07-06 02:31:06] Total                mtp: 15.37Mh/s, avg 15.05Mh/s, pool 5.764Mh/s a:9 r:0 hw:0

    it works ,thanks
    GPU0=vega56
    orthers=vega64

    power per card 200w

  • joseph32
    Member
    **
    Offline Offline

    Activity: 418
    Merit: 21


    View Profile
    July 06, 2019, 04:03:33 AM
     #618
    Hey Todxx & Kerney666,

    thanks for the quick fix! It runs now perfect with AwesomeMiner!

  • todxx (OP)
    Member
    **
    Offline Offline

    Activity: 176
    Merit: 76


    View Profile
    July 07, 2019, 05:23:50 AM
     #619
    Team Red Miner v0.5.5 released

    https://github.com/todxx/teamredminer/releases

    Changes in v0.5.5
    • Added cuckatoo31 algo for grin.

    We've added cuckatoo31 for grin mining!
    Seems we might have been a bit late as asics are might already be here for the algo  Sad.

  • ku4eto
    Jr. Member
    *
    Offline Offline

    Activity: 193
    Merit: 4


    View Profile
    July 07, 2019, 06:42:07 AM
     #620
    Quote from: todxx on July 07, 2019, 05:23:50 AM
    Team Red Miner v0.5.5 released

    https://github.com/todxx/teamredminer/releases

    Changes in v0.5.5
    • Added cuckatoo31 algo for grin.

    We've added cuckatoo31 for grin mining!
    Seems we might have been a bit late as asics are might already be here for the algo  Sad.
    They have been up since the coin launched.
    Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 [31] 32 33 34 35 36 37 38 39 40 41 42 »
      Print  
Page 30
Viewing Page: 31

IRLBTC™ © 2025 IRLBTC.com