<<  >> (p.568)
    Author Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)  (Read 6591467 times)

    • lazyturtle
    Newbie
    *
    Offline Offline

    Activity: 37
    Merit: 0


    View Profile
    June 05, 2017, 05:11:04 PM
     #11341
    Quote from: TechPark on June 05, 2017, 05:23:46 AM
    Quote from: lazyturtle on June 03, 2017, 09:40:54 PM
    Hello everyone. I have a problem with one of my rigs.

    I get the ""WATCHDOG: GPU 0 hangs in OpenCL call, exit" problem after about 20-60 min running the claymore miner. It started tough with that my miner was loosing internet connection after running a while. When i fixed that by installing new network adapter drivers, the connection was stable but the GPU´s started to give 0.00 mh´s after a while, until getting the error message.

    I did overclock the rig in the beggining, but i have reseted the MSI afterburner settings to default and i also did a bios mod, but i flashed the cards back to the original bios. I also dont think that the bios mod was the problem, because i have 3 more rigs with rx 470 with the same mod, and they all work great.

    Specs:
    Intel Celeron G1840 Processor
    Asrock H81 Pro BTC motherboard
    6x AMD Radeon RX 470 4GB
    4GB DDR3 Memory
    60GB SDD Harddisk
    1000W Gold power supply
    Windows 10 operating system

    I have already tried to:
    - Run the miner with the gser and eser commands and have also tried both dual and solo mining(both have same problems).
    - fresh install of both operating system and Gpu drivers (first gpu drivers with DDU and after that operating system).
    - Checked every riser, but they all work on a diffrent system so thats not the problem.
    - Setting virtual memory to atleast 16000
    - Tried old claymore miners, from 6.3 and up, same problem.

    I dont really know what to do at this point, would really appreciate help if someone knows what might be causing this. Smiley

    leave 1 card only, remove other cards a mine for 2 hours. If the miner does not crash replace the card and repeat the test. If you do not find a "faulty card" by trying all 6 then start adding cards - two for 2 hours, 3 for 2 hours, 4 for 2 hours, 5 for 2 hours and finally 6. Post the results of these tests here.

    Thanks for the answer, i managed to solve it. I did the tests and no hardware was faulty, acctually it seemed like there was some weird bug where msi afterburner would keep my overclocked settings and not going back to default even though set it to do so. Appreciate the help anyway, thanks Smiley

  • lazyturtle
    Newbie
    *
    Offline Offline

    Activity: 37
    Merit: 0


    View Profile
    June 05, 2017, 05:12:44 PM
     #11342
    Quote from: Xardas2014 on June 05, 2017, 06:43:55 AM
    Quote from: TechPark on June 05, 2017, 05:23:46 AM
    Quote from: lazyturtle on June 03, 2017, 09:40:54 PM
    Hello everyone. I have a problem with one of my rigs.

    I get the ""WATCHDOG: GPU 0 hangs in OpenCL call, exit" problem after about 20-60 min running the claymore miner. It started tough with that my miner was loosing internet connection after running a while. When i fixed that by installing new network adapter drivers, the connection was stable but the GPU´s started to give 0.00 mh´s after a while, until getting the error message.

    I did overclock the rig in the beggining, but i have reseted the MSI afterburner settings to default and i also did a bios mod, but i flashed the cards back to the original bios. I also dont think that the bios mod was the problem, because i have 3 more rigs with rx 470 with the same mod, and they all work great.

    Specs:
    Intel Celeron G1840 Processor
    Asrock H81 Pro BTC motherboard
    6x AMD Radeon RX 470 4GB
    4GB DDR3 Memory
    60GB SDD Harddisk
    1000W Gold power supply
    Windows 10 operating system

    I have already tried to:
    - Run the miner with the gser and eser commands and have also tried both dual and solo mining(both have same problems).
    - fresh install of both operating system and Gpu drivers (first gpu drivers with DDU and after that operating system).
    - Checked every riser, but they all work on a diffrent system so thats not the problem.
    - Setting virtual memory to atleast 16000
    - Tried old claymore miners, from 6.3 and up, same problem.

    I dont really know what to do at this point, would really appreciate help if someone knows what might be causing this. Smiley

    leave 1 card only, remove other cards a mine for 2 hours. If the miner does not crash replace the card and repeat the test. If you do not find a "faulty card" by trying all 6 then start adding cards - two for 2 hours, 3 for 2 hours, 4 for 2 hours, 5 for 2 hours and finally 6. Post the results of these tests here.
    First thing I would check is to see if Win10 changing virtual mem settings during an update(which I see you checked), or updated the drivers. Both things are on the same pop up. After checking virtual mem on the advance tab, click on the hardware tab and tell winblows to not update drivers. Winblows will update drivers as it boots. Also what are the card temps when they shut down or start spitting out opencl errors?

    The temps variate between 62-70 at most at all times. I did solve this issue tough, but thanks for the response, was a weird bug in msi afterburner that would not reset my overclocking properly Smiley Thanks anyway, peace!

  • fury420
    Newbie
    *
    Offline Offline

    Activity: 51
    Merit: 0


    View Profile
    June 05, 2017, 06:27:24 PM
     #11343
    @Claymore,

    I've now been able to replicate the EthMan bug with as few as 3 miner entries, tested on both Win 7 x64 and Win 10 machines.

    Freshly generated config file with three local IPs added, only one of which has a running miner. (ETH 9.4)
    Leave open for 5-10min, crashes every time. (all miners shown as red/offline)

  • samhayne
    Jr. Member
    *
    Offline Offline

    Activity: 40
    Merit: 1


    View Profile
    June 05, 2017, 07:10:37 PM
     #11344
    So... there just seems to be no way to use an GTX 970 properly for mining with Win 10 (1703).

    after googling and testing for an entire day...

    382.33 + CUDA 8.0: 3 MH/s
    372.54 + CUDA 6.5: 9.5 MH/s (with P0)
    347.52 + CUDA 6.5: 16.5 MH/s (driver won't allow P0 setting)

     Embarrassed

  • sp00lin9
    Hero Member
    *****
    Offline Offline

    Activity: 490
    Merit: 500


    View Profile
    June 05, 2017, 07:44:29 PM
     #11345
    Quote from: samhayne on June 05, 2017, 07:10:37 PM
    So... there just seems to be no way to use an GTX 970 properly for mining with Win 10 (1703).

    after googling and testing for an entire day...

    382.33 + CUDA 8.0: 3 MH/s
    372.54 + CUDA 6.5: 9.5 MH/s (with P0)
    347.52 + CUDA 6.5: 16.5 MH/s (driver won't allow P0 setting)

     Embarrassed


    Try using Linux, that's what I use to avoid all that..

  • ccminer.net
    Sr. Member
    ****
    Offline Offline

    Activity: 595
    Merit: 251


    View Profile
    June 05, 2017, 07:51:14 PM
     #11346
    Exuse me for the stupid question, but how to set up the environmental variables in ubuntu?

  • cashen
    Sr. Member
    ****
    Offline Offline

    Activity: 434
    Merit: 251


    View Profile
    June 05, 2017, 09:55:56 PM
     #11347
    I'm interested in getting my Remote Manager Ethman.exe working

    When a rig drops below a given hash rate it executes a BAT file. Does it execute the bate file on the rig with the low hash rate or the the machine where ethman is running?

    Do I run ethman on all my rigs?

  • AlainC
    Member
    **
    Offline Offline

    Activity: 91
    Merit: 10


    View Profile
    June 05, 2017, 09:59:46 PM
     #11348
    Quote from: ccminer.net on June 05, 2017, 07:51:14 PM
    Exuse me for the stupid question, but how to set up the environmental variables in ubuntu?
    depend on the shell, but with bash,
    export VAR=value

  • AlainC
    Member
    **
    Offline Offline

    Activity: 91
    Merit: 10


    View Profile
    June 05, 2017, 10:06:29 PM
     #11349
    About environnement variables, on ubuntu 16.04.2, with Claymore 9.4, amdgpu-pro-17.10-414273,
    I enjoy those variables settings:
    Code:
    GPU_FORCE_64BIT_PTR=1
    GPU_MAX_HEAP_SIZE=100
    GPU_USE_SYNC_OBJECTS=1
    GPU_MAX_ALLOC_PERCENT=100
    GPU_SINGLE_ALLOC_PERCENT=100
    and ethdcrminer64 runs like a charm

    if I put
    Code:
    GPU_FORCE_64BIT_PTR=0
    as advised, it crashes with
    Code:
    segfault at 8 ip 00007f37c1d1ba0c sp 00007f37bdea7d10 error 4 in libamdocl64.so[7f37c161f000+3dfb000]
    No problem, it works, but it may be interesting for beginner to know.

  • ccminer.net
    Sr. Member
    ****
    Offline Offline

    Activity: 595
    Merit: 251


    View Profile
    June 05, 2017, 10:19:25 PM
     #11350
    Quote from: AlainC on June 05, 2017, 10:06:29 PM
    About environnement variables, on ubuntu 16.04.2, with Claymore 9.4, amdgpu-pro-17.10-414273,
    I enjoy those variables settings:
    Code:
    GPU_FORCE_64BIT_PTR=1
    GPU_MAX_HEAP_SIZE=100
    GPU_USE_SYNC_OBJECTS=1
    GPU_MAX_ALLOC_PERCENT=100
    GPU_SINGLE_ALLOC_PERCENT=100
    and ethdcrminer64 runs like a charm

    if I put
    Code:
    GPU_FORCE_64BIT_PTR=0
    as advised, it crashes with
    Code:
    segfault at 8 ip 00007f37c1d1ba0c sp 00007f37bdea7d10 error 4 in libamdocl64.so[7f37c161f000+3dfb000]
    No problem, it works, but it may be interesting for beginner to know.

    So I have just to tape on terminal

    export GPU_MAX_HEAP_SIZE=100
    and so on?

    and than run the miner?

  • Digggger
    Newbie
    *
    Offline Offline

    Activity: 21
    Merit: 0


    View Profile
    June 05, 2017, 10:21:26 PM
     #11351
    Hey guys, a couple problems I haven't been able to solve. Not sure if it's a claymore issue or something else.

    6 rx 570's with bios' modded. GPU0 overclocks as expected with Afterburner, 25MH/s with no OC... 27MH/s with a little overclocking and undervolting. All other GPU's are not affected by the overclocking but will undervolt. Yes the synchronize similar GPU's is on. I tried it with it off and overclocked each GPU on its own, same result...only GPU0 has a change in hash rates.

    Same issue with my gaming pc with 2 rx480's...GPU0 hash rate changes but GPU1 is unchanged...GPU-Z confirms the memory clock is rising.

  • AlainC
    Member
    **
    Offline Offline

    Activity: 91
    Merit: 10


    View Profile
    June 05, 2017, 10:39:07 PM
     #11352
    Quote from: ccminer.net on June 05, 2017, 10:19:25 PM
    So I have just to tape on terminal

    export GPU_MAX_HEAP_SIZE=100
    and so on?

    and than run the miner?

    ? I don't catch alll...
    to run you can write a script... Claymore propose one (for ETH only here):
    Code:
    #!/bin/bash
    export GPU_FORCE_64BIT_PTR=0
    export GPU_MAX_HEAP_SIZE=100
    export GPU_USE_SYNC_OBJECTS=1
    export GPU_MAX_ALLOC_PERCENT=100
    export GPU_SINGLE_ALLOC_PERCENT=100

    ./ethdcrminer64 -epool eth-eu1.nanopool.org:9999 -ewal YOUR_WALLET/YOUR_WORKER/YOUR_EMAIL -epsw x -mode 1 -ftime 10
    have also to edit config.txt, epools.txt (and dpools.txt if you dual mine)

  • ccminer.net
    Sr. Member
    ****
    Offline Offline

    Activity: 595
    Merit: 251


    View Profile
    June 05, 2017, 10:57:43 PM
     #11353
    Quote from: AlainC on June 05, 2017, 10:39:07 PM
    Quote from: ccminer.net on June 05, 2017, 10:19:25 PM
    So I have just to tape on terminal

    export GPU_MAX_HEAP_SIZE=100
    and so on?

    and than run the miner?

    ? I don't catch alll...
    to run you can write a script... Claymore propose one (for ETH only here):
    Code:
    #!/bin/bash
    export GPU_FORCE_64BIT_PTR=0
    export GPU_MAX_HEAP_SIZE=100
    export GPU_USE_SYNC_OBJECTS=1
    export GPU_MAX_ALLOC_PERCENT=100
    export GPU_SINGLE_ALLOC_PERCENT=100

    ./ethdcrminer64 -epool eth-eu1.nanopool.org:9999 -ewal YOUR_WALLET/YOUR_WORKER/YOUR_EMAIL -epsw x -mode 1 -ftime 10
    have also to edit config.txt, epools.txt (and dpools.txt if you dual mine)

    how to edit the conf file?

    Sorry again for the stupid question

  • matttheazn
    Newbie
    *
    Offline Offline

    Activity: 8
    Merit: 0


    View Profile
    June 05, 2017, 10:58:01 PM
     #11354
    Hi I am having trouble with setting a stop temperature and restarting the miner.  In my command line I have "-wd 1 -r 1 -tstop 90"  I have a reboot.bat(windows 10) file with a shutdown command in the same directory.  When I hit the bat it will shutdown the computer.  For testing purposes I am using -tstop 55.  It stops mining correctly but how to I get it to execute the reboot.bat file?   What am I doing wrong?    thanks

  • frostminer
    Hero Member
    *****
    Offline Offline

    Activity: 742
    Merit: 505


    View Profile WWW
    June 05, 2017, 11:02:03 PM
     #11355
    Quote from: Digggger on June 05, 2017, 10:21:26 PM
    Hey guys, a couple problems I haven't been able to solve. Not sure if it's a claymore issue or something else.

    6 rx 570's with bios' modded. GPU0 overclocks as expected with Afterburner, 25MH/s with no OC... 27MH/s with a little overclocking and undervolting. All other GPU's are not affected by the overclocking but will undervolt. Yes the synchronize similar GPU's is on. I tried it with it off and overclocked each GPU on its own, same result...only GPU0 has a change in hash rates.

    Same issue with my gaming pc with 2 rx480's...GPU0 hash rate changes but GPU1 is unchanged...GPU-Z confirms the memory clock is rising.


    I had some weird issues on a rx 480 rigs thats seems a bit similar.
    In the end it was reinstalling afterburner that fixed it .. never made any sense.



    (Lucky you getting a hold of rx 5xx at all... im still waiting another week for my batch)

  • ozzy1926
    Sr. Member
    ****
    Offline Offline

    Activity: 378
    Merit: 250


    View Profile
    June 05, 2017, 11:22:20 PM
     #11356
    I have been mining more than 48 hours and when i check the miner the hashrate is always at 42.9 but today my avarage hashrate starts to dop what could be the problem?

  • djazher
    Newbie
    *
    Offline Offline

    Activity: 41
    Merit: 0


    View Profile
    June 05, 2017, 11:46:11 PM
     #11357
    Quote from: samhayne on June 05, 2017, 07:10:37 PM
    So... there just seems to be no way to use an GTX 970 properly for mining with Win 10 (1703).

    after googling and testing for an entire day...

    382.33 + CUDA 8.0: 3 MH/s
    372.54 + CUDA 6.5: 9.5 MH/s (with P0)
    347.52 + CUDA 6.5: 16.5 MH/s (driver won't allow P0 setting)

     Embarrassed


    Why don't you switch to Win7, at least to get it out of your head ? 970 DO hash, not the most efficient results, but this GPU is 3 years old already. Like I said, I learned with 2 of them, and was getting 24MH/s per card, @180W [free electricity, I OC'd them to hellish limits]

  • Digggger
    Newbie
    *
    Offline Offline

    Activity: 21
    Merit: 0


    View Profile
    June 05, 2017, 11:50:26 PM
     #11358
    Quote from: frostminer on June 05, 2017, 11:02:03 PM
    Quote from: Digggger on June 05, 2017, 10:21:26 PM
    Hey guys, a couple problems I haven't been able to solve. Not sure if it's a claymore issue or something else.

    6 rx 570's with bios' modded. GPU0 overclocks as expected with Afterburner, 25MH/s with no OC... 27MH/s with a little overclocking and undervolting. All other GPU's are not affected by the overclocking but will undervolt. Yes the synchronize similar GPU's is on. I tried it with it off and overclocked each GPU on its own, same result...only GPU0 has a change in hash rates.

    Same issue with my gaming pc with 2 rx480's...GPU0 hash rate changes but GPU1 is unchanged...GPU-Z confirms the memory clock is rising.


    I had some weird issues on a rx 480 rigs thats seems a bit similar.
    In the end it was reinstalling afterburner that fixed it .. never made any sense.



    (Lucky you getting a hold of rx 5xx at all... im still waiting another week for my batch)

    Thanks I'll try it.

    Yes I'd like to find some more!

  • lazyturtle
    Newbie
    *
    Offline Offline

    Activity: 37
    Merit: 0


    View Profile
    June 06, 2017, 12:00:30 AM
     #11359
    Quote from: ozzy1926 on June 05, 2017, 11:22:20 PM
    I have been mining more than 48 hours and when i check the miner the hashrate is always at 42.9 but today my avarage hashrate starts to dop what could be the problem?
    https://i.hizliresim.com/nWY1j5.jpg

    Your effective hashrate is calculated by the shares your miner manages to accept.

    With that said its a variable that does not always follow your exact hashrate. It is normal with variations, sometimes it´s higher and sometimes it´s lower then what your current reported hashrate is.Smiley

  • drak24
    Newbie
    *
    Offline Offline

    Activity: 22
    Merit: 0


    View Profile
    June 06, 2017, 02:15:06 AM
     #11360
    Can't seem to get a good stable OC for the death of me lol. Any suggestions?

    My dual mining hashrate for ETH currently fluctuates between 42-48Mh/s from two 8Gb Strix RX 480s, with one card around 20-23Mh/s and the other 24-25Mh/s. I've read that people are able to get 30-31Mh/s from these cards through OC but outside of the default OC at 1330Mhz in GPU Tweak 2, everything crashes after a while. I had managed to get to 51Mh/s but it crashed. My rig is as follows and any help/guidance would be appreciated.

    Ryzen 7 1700x
    Asrock x370 Taichi Mobo
    Corsair H100i v2 Liquid Cooling
    (2) Asus Strix RX 480 8GB running with Crossfire - Driver 17.10.1731
    32Gb Ram
    750W Power Supply
    1 SSD, 2 Sata HDDs
    NZXT Phantom with 5 fans (1 200mm, 4 140mm)
    Windows 10 64bit

    Any ideas or advice on getting up to 50-60Mh/s?

    Edit: It just crashed on the default OC as well.. smh
    Pages: « 1 ... 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 [568] 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 ... 1410 »
      Print  
Page 567
Viewing Page: 568

IRLBTC™ © 2025 IRLBTC.com