<<  >> (p.996)
    Author Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)  (Read 6591480 times)

    • Redstar007
    Newbie
    *
    Offline Offline

    Activity: 6
    Merit: 0


    View Profile
    February 12, 2018, 09:05:35 PM
     #19901
    @Claymore. Seems someone tried to hack my rig. Is it something besides readonly I can do to maximize the security?

    21:07:13:777   16c   srv_thr cnt: 1, IP: 185.62.188.88
    21:07:13:933   16c   recv: 347
    21:07:13:933   16c   srv pck: 347
    21:07:13:933   16c   Remote management: read-only mode, command miner_file ignored. Remote IP: 185.62.188.88
    21:07:13:933   16c   srv bs: 0
    21:07:16:527   67c   ETH: checking pool connection...
    21:07:16:527   67c   send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}

    21:07:16:558   67c   got 243 bytes
    21:07:16:558   67c   buf: {"jsonrpc":"2.0","id":0,"result":["0x7cb5899436b86f505c1cc5e84dc220ea0c6e76dbd777843acd6d457a88cab564","0xa74dd84414948aba4bfd6580908dbf9c32a494aa336609746d19a35bb4cccb24","0x000000006df37f675ef6eadf5ab9a2072d44268d97df837e6748956e5c6c2116"]}

    21:07:16:558   67c   parse packet: 242
    21:07:16:558   67c   ETH: job is the same
    21:07:16:558   67c   new buf size: 0
    21:07:18:965   9c   srv_thr cnt: 1, IP: 185.62.188.88
    21:07:19:012   67c   got 243 bytes
    21:07:19:012   67c   buf: {"jsonrpc":"2.0","id":0,"result":["0xeea17940990748fd89c454e57072aaf185d9c1785a5885480afd15f60041cbf0","0xa74dd84414948aba4bfd6580908dbf9c32a494aa336609746d19a35bb4cccb24","0x000000006df37f675ef6eadf5ab9a2072d44268d97df837e6748956e5c6c2116"]}

    21:07:19:012   67c   parse packet: 242
    21:07:19:012   67c   ETH: job changed
    21:07:19:012   67c   new buf size: 0
    21:07:19:012   67c   ETH: 02/12/18-21:07:19 - New job from etc-eu1.nanopool.org:19999
    21:07:19:012   67c   target: 0x000000006df37f67 (diff: 10000MH), epoch 179(2.40GB)
    21:07:19:012   67c   ETH - Total Speed: 180.527 Mh/s, Total Shares: 71, Rejected: 0, Time: 01:19
    21:07:19:012   67c   ETH: GPU0 29.654 Mh/s, GPU1 30.187 Mh/s, GPU2 30.176 Mh/s, GPU3 30.185 Mh/s, GPU4 30.168 Mh/s, GPU5 30.156 Mh/s
    21:07:19:324   9c   recv: 48
    21:07:19:324   9c   srv pck: 48
    21:07:19:324   9c   Remote management: read-only only, command miner_reboot ignored. Remote IP: 185.62.188.88
    21:07:19:324   9c   srv bs: 0
    21:07:22:825   67c   send: {"id":6,"jsonrpc":"2.0","method":"eth_submitHashrate","params":["0xac31053", "0x00000000000000000000000000000000000000000000000000000000da52f972"]}


    Anyone else gotten this? When u look up the ip adress, no one else but the one and only Hitler appears.

  • Lamsterpaul
    Newbie
    *
    Offline Offline

    Activity: 19
    Merit: 0


    View Profile
    February 12, 2018, 09:07:27 PM
     #19902
    Got also had a working rig with 12 radeon r9 390 stabile running, but power use is high, i need 3 PSU to run it
    At this time 3 cards are down (power supply cable burns out), rest still works

    I also had a second rig with 10GPUs with the 4pin connector riser cards an an asus p10ws stabile for weeks

  • cryptoillusion1
    Newbie
    *
    Offline Offline

    Activity: 82
    Merit: 0


    View Profile
    February 12, 2018, 09:35:35 PM
     #19903
    Quote from: Redstar007 on February 12, 2018, 09:05:35 PM
    @Claymore. Seems someone tried to hack my rig. Is it something besides readonly I can do to maximize the security?

    21:07:13:777   16c   srv_thr cnt: 1, IP: 185.62.188.88
    21:07:13:933   16c   recv: 347
    21:07:13:933   16c   srv pck: 347
    21:07:13:933   16c   Remote management: read-only mode, command miner_file ignored. Remote IP: 185.62.188.88
    21:07:13:933   16c   srv bs: 0
    21:07:16:527   67c   ETH: checking pool connection...
    21:07:16:527   67c   send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}

    21:07:16:558   67c   got 243 bytes
    21:07:16:558   67c   buf: {"jsonrpc":"2.0","id":0,"result":["0x7cb5899436b86f505c1cc5e84dc220ea0c6e76dbd777843acd6d457a88cab564","0xa74dd84414948aba4bfd6580908dbf9c32a494aa336609746d19a35bb4cccb24","0x000000006df37f675ef6eadf5ab9a2072d44268d97df837e6748956e5c6c2116"]}

    Anyone else gotten this? When u look up the ip adress, no one else but the one and only Hitler appears.

    Use -mport 0

    mport   remote monitoring/management port. Default value is -3333 (read-only mode), specify "-mport 0" to disable remote monitoring/management feature

  • Redstar007
    Newbie
    *
    Offline Offline

    Activity: 6
    Merit: 0


    View Profile
    February 12, 2018, 10:15:34 PM
     #19904
    Quote from: cryptoillusion1 on February 12, 2018, 09:35:35 PM
    Quote from: Redstar007 on February 12, 2018, 09:05:35 PM
    @Claymore. Seems someone tried to hack my rig. Is it something besides readonly I can do to maximize the security?

    21:07:13:777   16c   srv_thr cnt: 1, IP: 185.62.188.88
    21:07:13:933   16c   recv: 347
    21:07:13:933   16c   srv pck: 347
    21:07:13:933   16c   Remote management: read-only mode, command miner_file ignored. Remote IP: 185.62.188.88
    21:07:13:933   16c   srv bs: 0
    21:07:16:527   67c   ETH: checking pool connection...
    21:07:16:527   67c   send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}

    21:07:16:558   67c   got 243 bytes
    21:07:16:558   67c   buf: {"jsonrpc":"2.0","id":0,"result":["0x7cb5899436b86f505c1cc5e84dc220ea0c6e76dbd777843acd6d457a88cab564","0xa74dd84414948aba4bfd6580908dbf9c32a494aa336609746d19a35bb4cccb24","0x000000006df37f675ef6eadf5ab9a2072d44268d97df837e6748956e5c6c2116"]}

    Anyone else gotten this? When u look up the ip adress, no one else but the one and only Hitler appears.

    Use -mport 0

    mport   remote monitoring/management port. Default value is -3333 (read-only mode), specify "-mport 0" to disable remote monitoring/management feature

    Will do, thanks!

    Some info for you guys: https://www.bleepingcomputer.com/news/security/satori-botnet-is-now-attacking-ethereum-mining-rigs/

  • initcode
    Newbie
    *
    Offline Offline

    Activity: 3
    Merit: 0


    View Profile
    February 12, 2018, 10:17:44 PM
     #19905
    Hi everybody,

    I have the following problem.

    I have a rig with 7 RX580 mining ETH only with Claymore Miner.

    For more than a month I used the following:

    -tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925

    And worked fine by drawing around 850-900Watt.

    Suddenly something changed and now is hitting 1400Watt and I can't figure out why.

    I used this driver
    Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23

    but I also tried
    win10-64bit-radeon-software-adrenalin-edition-18.2.1-feb1 (i compute mode)

    and Miner version 10.4, miner 10.6 and today I tried v11.00


    No matter what I try the clock and voltage settings are been ignored.

    I noticed in the README file it says:
    Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

    Which drivers do not block?
    And why since I didn't change drivers that started happening?

    Any ideas?

    Thank you
    Initcode

  • aliscomputers
    Newbie
    *
    Offline Offline

    Activity: 19
    Merit: 0


    View Profile
    February 12, 2018, 10:21:10 PM
    Last edit: February 16, 2018, 12:52:45 AM by aliscomputers
     #19906
    Greetings miners,
    I just started new pool for XVG on blake2s algo(for ETH+XVG dual). I will be more than happy if you help to test it and see if everything is okay. We set up only 0.5% fee and in next days or week expect more coins to mine or even few more algos.

    BTCstratum+tcp://verge.ehu.bg:5766 BTC

    Kind Regards!
    Enjoy  Smiley

  • sebastian103
    Newbie
    *
    Offline Offline

    Activity: 2
    Merit: 0


    View Profile
    February 12, 2018, 10:28:39 PM
     #19907
    Quote from: initcode on February 12, 2018, 10:17:44 PM
    Hi everybody,

    I have the following problem.

    I have a rig with 7 RX580 mining ETH only with Claymore Miner.

    For more than a month I used the following:

    -tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925

    And worked fine by drawing around 850-900Watt.

    Suddenly something changed and now is hitting 1400Watt and I can't figure out why.

    I used this driver
    Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23

    but I also tried
    win10-64bit-radeon-software-adrenalin-edition-18.2.1-feb1 (i compute mode)

    and Miner version 10.4, miner 10.6 and today I tried v11.00




    No matter what I try the clock and voltage settings are been ignored.

    I noticed in the README file it says:
    Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

    Which drivers do not block?
    And why since I didn't change drivers that started happening?

    Any ideas?

    Thank you
    Initcode




    I had similiar issue. I had this in config file but after loading the miner in was not in command line. Check if u have this "-tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925" in the end of command lien after starting the miner" For some reason i had to rewrite "start" to work it again. Happend after switching to v 11

  • NN900
    Newbie
    *
    Offline Offline

    Activity: 105
    Merit: 0


    View Profile
    February 12, 2018, 10:50:11 PM
     #19908
    Good evening! Anybody trying to mine smartcash (keccak) as a dual coin? Trying this pool https://pool-eu.smartcash.cc but no matter what DCRI setting I use (4, 5, 6, 7) I get 100% Keccak rejects.

  • Teress
    Full Member
    ***
    Offline Offline

    Activity: 224
    Merit: 102


    View Profile
    February 12, 2018, 10:52:27 PM
     #19909
    Quote from: NN900 on February 12, 2018, 10:50:11 PM
    Good evening! Anybody trying to mine smartcash (keccak) as a dual coin? Trying this pool https://pool-eu.smartcash.cc but no matter what DCRI setting I use (4, 5, 6, 7) I get 100% Keccak rejects.

    I have also 100% keccak rejects on all other pools I tried and different coin.

  • initcode
    Newbie
    *
    Offline Offline

    Activity: 3
    Merit: 0


    View Profile
    February 12, 2018, 11:08:55 PM
     #19910
    Quote from: sebastian103 on February 12, 2018, 10:28:39 PM
    Quote from: initcode on February 12, 2018, 10:17:44 PM
    Hi everybody,

    I have the following problem.

    I have a rig with 7 RX580 mining ETH only with Claymore Miner.

    For more than a month I used the following:

    -tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925

    And worked fine by drawing around 850-900Watt.

    Suddenly something changed and now is hitting 1400Watt and I can't figure out why.

    I used this driver
    Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23

    but I also tried
    win10-64bit-radeon-software-adrenalin-edition-18.2.1-feb1 (i compute mode)

    and Miner version 10.4, miner 10.6 and today I tried v11.00




    No matter what I try the clock and voltage settings are been ignored.

    I noticed in the README file it says:
    Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

    Which drivers do not block?
    And why since I didn't change drivers that started happening?

    Any ideas?

    Thank you
    Initcode




    I had similiar issue. I had this in config file but after loading the miner in was not in command line. Check if u have this "-tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925" in the end of command lien after starting the miner" For some reason i had to rewrite "start" to work it again. Happend after switching to v 11

    Thank you for the reply,

    I'm afraid I do not have this problem.
    I can see all these settings in the command line on top.

  • darkdude
    Jr. Member
    *
    Offline Offline

    Activity: 113
    Merit: 1


    View Profile
    February 12, 2018, 11:10:22 PM
     #19911
    right now at 29.5s for eth for 580 4gb.  mem clock at 2000, and while i can increase the mem clock (ie. 2100+) , i begin to see mem errors with hwinfo on my gpu.  claymore seems fine, and i can reach 31s but with massive mem errors in hwinfo, but again claymore seems fine.

    Is it best I drop back to 2000 when I had no mem errors, or should I go as high as I can on the mem clock until I see the hashrate drop or claymore become unstable?

    Thoughts?

  • Teress
    Full Member
    ***
    Offline Offline

    Activity: 224
    Merit: 102


    View Profile
    February 12, 2018, 11:46:23 PM
     #19912
    Quote from: darkdude on February 12, 2018, 11:10:22 PM
    right now at 29.5s for eth for 580 4gb.  mem clock at 2000, and while i can increase the mem clock (ie. 2100+) , i begin to see mem errors with hwinfo on my gpu.  claymore seems fine, and i can reach 31s but with massive mem errors in hwinfo, but again claymore seems fine.

    Is it best I drop back to 2000 when I had no mem errors, or should I go as high as I can on the mem clock until I see the hashrate drop or claymore become unstable?

    Thoughts?

    Decrease your mem clock until you get no mem errors. Or try different mem strap.

  • muzuca
    Member
    **
    Offline Offline

    Activity: 182
    Merit: 13


    View Profile
    February 12, 2018, 11:55:57 PM
     #19913
    Quote from: initcode on February 12, 2018, 11:08:55 PM
    Quote from: sebastian103 on February 12, 2018, 10:28:39 PM
    Quote from: initcode on February 12, 2018, 10:17:44 PM
    Hi everybody,

    I have the following problem.

    I have a rig with 7 RX580 mining ETH only with Claymore Miner.

    For more than a month I used the following:

    -tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925

    And worked fine by drawing around 850-900Watt.

    Suddenly something changed and now is hitting 1400Watt and I can't figure out why.

    I used this driver
    Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23

    but I also tried
    win10-64bit-radeon-software-adrenalin-edition-18.2.1-feb1 (i compute mode)

    and Miner version 10.4, miner 10.6 and today I tried v11.00




    No matter what I try the clock and voltage settings are been ignored.

    I noticed in the README file it says:
    Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

    Which drivers do not block?
    And why since I didn't change drivers that started happening?

    Any ideas?

    Thank you
    Initcode




    I had similiar issue. I had this in config file but after loading the miner in was not in command line. Check if u have this "-tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925" in the end of command lien after starting the miner" For some reason i had to rewrite "start" to work it again. Happend after switching to v 11

    Thank you for the reply,

    I'm afraid I do not have this problem.
    I can see all these settings in the command line on top.


    Once I have this problem and to fix I open and close the miner for 2-3 times to fix the config... the trick is wait until the last setting dag file and then close.
    ▌▌   Anonymous and Untraceable     ›› ››   DeepOnion  ‹‹ ‹‹     TOR INTEGRATED & SECURED    ▌▌
    ▬▬▬▬▬▬▬▬▬▬     ANN  Whitepaper  FACEBOOK  Twitter  Youtube  Forum     ▬▬▬▬▬▬▬▬▬▬
    ▌▌   ••  JOIN AIRDROP 🚀  ••  |||   Download DeepOnion   |||   ✅ Verified with DeepVault    ▌▌

  • muzuca
    Member
    **
    Offline Offline

    Activity: 182
    Merit: 13


    View Profile
    February 12, 2018, 11:58:23 PM
     #19914
    Quote from: darkdude on February 12, 2018, 11:10:22 PM
    right now at 29.5s for eth for 580 4gb.  mem clock at 2000, and while i can increase the mem clock (ie. 2100+) , i begin to see mem errors with hwinfo on my gpu.  claymore seems fine, and i can reach 31s but with massive mem errors in hwinfo, but again claymore seems fine.

    Is it best I drop back to 2000 when I had no mem errors, or should I go as high as I can on the mem clock until I see the hashrate drop or claymore become unstable?

    Thoughts?

    Check if you are having shares lost because of the mem errors. In my case I have some GPUs that has a few thousands errors but are working just fine... once a time I need to restart the rig, but isn’t often.
    ▌▌   Anonymous and Untraceable     ›› ››   DeepOnion  ‹‹ ‹‹     TOR INTEGRATED & SECURED    ▌▌
    ▬▬▬▬▬▬▬▬▬▬     ANN  Whitepaper  FACEBOOK  Twitter  Youtube  Forum     ▬▬▬▬▬▬▬▬▬▬
    ▌▌   ••  JOIN AIRDROP 🚀  ••  |||   Download DeepOnion   |||   ✅ Verified with DeepVault    ▌▌

  • initcode
    Newbie
    *
    Offline Offline

    Activity: 3
    Merit: 0


    View Profile
    February 13, 2018, 12:25:07 AM
     #19915
    Quote from: muzuca on February 12, 2018, 11:55:57 PM
    Quote from: initcode on February 12, 2018, 11:08:55 PM
    Quote from: sebastian103 on February 12, 2018, 10:28:39 PM
    Quote from: initcode on February 12, 2018, 10:17:44 PM
    Hi everybody,

    I have the following problem.

    I have a rig with 7 RX580 mining ETH only with Claymore Miner.

    For more than a month I used the following:

    -tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925

    And worked fine by drawing around 850-900Watt.

    Suddenly something changed and now is hitting 1400Watt and I can't figure out why.

    I used this driver
    Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23

    but I also tried
    win10-64bit-radeon-software-adrenalin-edition-18.2.1-feb1 (i compute mode)

    and Miner version 10.4, miner 10.6 and today I tried v11.00




    No matter what I try the clock and voltage settings are been ignored.

    I noticed in the README file it says:
    Note: for some drivers versions AMD blocked underclocking for some reason, you can overclock only.

    Which drivers do not block?
    And why since I didn't change drivers that started happening?

    Any ideas?

    Thank you
    Initcode




    I had similiar issue. I had this in config file but after loading the miner in was not in command line. Check if u have this "-tstop 85 -tt 65 -fanmin 50 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 925 -mvddc 925" in the end of command lien after starting the miner" For some reason i had to rewrite "start" to work it again. Happend after switching to v 11

    Thank you for the reply,

    I'm afraid I do not have this problem.
    I can see all these settings in the command line on top.


    Once I have this problem and to fix I open and close the miner for 2-3 times to fix the config... the trick is wait until the last setting dag file and then close.

    SOLVED!

    I found the problem!!!

    It was the Remote Desktop Connection

    If you start Claymore miner remotely using Remote Desktop Connection and you check the logs you will see that it reports that there are no AMD Adapters.
    ADL: Cannot find any AMD adapters

    The miner will start, it will mine but it will ignore any overclock/undervolt settings for the cards!

    I spent 2 days on that!!
    I hope that will help some of you.

    Please note that this problem does not occur if you use Teamviewer

    Thank you
    Initcode

  • blackwhite5674
    Newbie
    *
    Offline Offline

    Activity: 5
    Merit: 0


    View Profile
    February 13, 2018, 12:45:28 AM
     #19916
    Quote from: Teress on February 12, 2018, 10:52:27 PM
    Quote from: NN900 on February 12, 2018, 10:50:11 PM
    Good evening! Anybody trying to mine smartcash (keccak) as a dual coin? Trying this pool https://pool-eu.smartcash.cc but no matter what DCRI setting I use (4, 5, 6, 7) I get 100% Keccak rejects.

    I have also 100% keccak rejects on all other pools I tried and different coin.

    -dpool stratum+tcp://pool-us.smartcash.cc:3333 -dwal USERNAME.WORKERNAME -dcoin keccak -dpsw PW -dcri 7 -allpools 1

    This has worked for me thus far. The workername and password needs to be created in My Account > My Workers and the username is chosen when you register. If you've already done this, then I'm not sure what else it could be, maybe try the US pool? Also not even sure if -allpools 1 is required tbh, haven't tried without...

    Setting dcri to anything higher seems to significantly impact ETH mh, I've found 7 to be best without losing too much.

  • letaro
    Newbie
    *
    Offline Offline

    Activity: 1
    Merit: 0


    View Profile
    February 13, 2018, 01:58:20 AM
     #19917
    Anyone have problem with unimining? due whattomine, i must earned 3 XVG per hour, 77 XVG per day but actually, i only earned 1 XVG per hour and after 18 hour i only earn 25 XVG? what is wrong in here? whattomine calculate wrong or pool is wrong?
    My rig is sapphire rx 470, and my hashrate for XVG is 8600 MHs.

    Anyone suggest me other pool to try?

  • svdinu
    Newbie
    *
    Offline Offline

    Activity: 34
    Merit: 0


    View Profile
    February 13, 2018, 03:34:01 AM
     #19918
    Quote from: Lamsterpaul on February 12, 2018, 09:07:27 PM
    Got also had a working rig with 12 radeon r9 390 stabile running, but power use is high, i need 3 PSU to run it
    At this time 3 cards are down (power supply cable burns out), rest still works

    I also had a second rig with 10GPUs with the 4pin connector riser cards an an asus p10ws stabile for weeks


    Any modded bios to reduce power consumption?

  • zz0622
    Newbie
    *
    Offline Offline

    Activity: 14
    Merit: 0


    View Profile
    February 13, 2018, 03:46:44 AM
     #19919
    Quote from: letaro on February 13, 2018, 01:58:20 AM
    Anyone have problem with unimining? due whattomine, i must earned 3 XVG per hour, 77 XVG per day but actually, i only earned 1 XVG per hour and after 18 hour i only earn 25 XVG? what is wrong in here? whattomine calculate wrong or pool is wrong?
    My rig is sapphire rx 470, and my hashrate for XVG is 8600 MHs.

    Anyone suggest me other pool to try?
    I have same problem too. According to Whattomine I should get 400 XVG one day, but Unimining only give me 200 which is only 50% of my hash power.

    Antminepool gives correct numbers, but it's often full

    Anyone suggest other pools?

  • greatauror28
    Full Member
    ***
    Offline Offline

    Activity: 181
    Merit: 101

    Ethereum Miner


    View Profile
    February 13, 2018, 04:11:46 AM
     #19920
    Just want to report that v11 is stable and brings no issues.

    It actually gives me cards .1 Mh  Grin

    Also more stable and less fluctuation of hashrates.
    I build and sell rigs! I also sell ssd clones of the most stable Windows+Claymore+AMD driver combo you'd ever used.
    Pages: « 1 ... 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 [996] 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 ... 1409 »
      Print  
Page 995
Viewing Page: 996

IRLBTC™ © 2025 IRLBTC.com